Results 1 to 10 of 11
-
01-27-2014, 12:42 PM #1Junior Member
- Join Date
- Jan 2014
- Posts
- 2
Part needed for my 2000 Moomba Mobius but do not know what it is called???
I need to find a replacement part for our 2000 Moomba Mobuis but not sure what the part name is. It's located on the back lower portion of the boat & there is one of each side. Please see the attached picture. We believe it is part of the ballast system where the water is sucked it but not sure. Thanks for any help you can give!
-
01-27-2014, 12:54 PM #2
I think that is the speedo??? Others may know better
'08 Mobius LS. Sold
'18 Craz "TypeO"
REV10's, Revo6 xss, Kicker10, Kicker 12 CompR, various LED's
-
01-27-2014, 01:21 PM #3
I would concur -- looks like the speedo to me
Mike
2013 Outback V
- ballast: 900# rears / 400# center / 650# IBS
- audio: Exile SXT9Q x 2 towers / Kicker KM65 x 6 cabins / Xi 12 sub / Javelin & XM15.4 amps / ZLD
- FAE
- DIY suckgate
2003 SeaRay 182 -- gone but not forgotten...
-
01-27-2014, 01:46 PM #4
Did it break off? If it isn't leaking time to install PP stargazer with GPS for speed.
-Mark
14 Mojo - 72 hours and growing
02 Mobius LSV ---- Sold and always will be remembered as the one that started it all.
"Hey you only live once"
-
01-27-2014, 03:00 PM #5Junior Member
- Join Date
- Jan 2014
- Posts
- 2
Thanks guys! That's what it is & going to get two new ones ordered!
-
01-27-2014, 03:51 PM #6Senior Member
- Join Date
- Aug 2011
- Posts
- 2,522
Re: Part needed for my 2000 Moomba Mobius but do not know what it is called???
Why bother, use that money for a prefect pass..
Sent from my Nexus 5 using Tapatalkhttp://www.instgram.com/jlyons30
2002 Moomba Mobius LSV - Sold
2006 Moomba Mobius LSV - Sold
2017 Moomba Craz - Enzos, Lead
-
01-27-2014, 05:59 PM #7Senior Member
- Join Date
- Dec 2006
- Location
- Tuscaloosa, Alabama
- Posts
- 815
It is called a pitot(sp) tube.
Jack Beams
'05 Outback DD
325HP EFI Indmar
-
01-27-2014, 09:37 PM #8Senior Member
- Join Date
- Oct 2013
- Location
- Ft. Collins, CO
- Posts
- 688
Why are you replacing them? Pitot tubes commonly get plugged with sediment and the result is the speedo fails. You can usually unscrew the tube and clean things out.
But if you didn't know it was part of the speedo... how did you know it needed to be replaced?2007 Mobius LSV
1989 Sanger Skier DX - sold
-
01-27-2014, 09:46 PM #9
Part needed for my 2000 Moomba Mobius but do not know what it is called???
^^^^^ this
Matt
2021 Mojo
2016 Mojo (sold)
2012 LSV (sold)
-
01-27-2014, 09:55 PM #10
Need to pull the line loose from the back of the speedometer and blow it out. They get water up in them sometimes. Or they get pinched. That's why you have two speedos for tournament use. If they were worth a crap you'd only need one. (By the way, you can make your boat a lot faster by drilling the hole out a little bit.)
My Mom said I'm not allowed to get wet!
2008 LSV (sold)
2000 Outback LS (sold)
LLTR!!!!!!!!