Results 21 to 30 of 64
Thread: Heater Install in 2006 LSV
-
04-24-2010, 01:56 PM #21Senior Member
- Join Date
- Jun 2008
- Location
- Eugene OR
- Posts
- 1,786
2008 Outback V - Sold but never forgotten.
“Do not wait; the time will never be “just right.” Start where you stand, and work with whatever tools you may have at your command, and better tools will be found as you go along." -Napoleon Hill
-
04-25-2010, 02:35 AM #22
Jester,
The Y is available at:
http://www.heatercraft.com/category....19&startpage=0
Thanks for the compliment. We are going out tomorrow and will be field testing it then. I will take some pics of the finished product and post it here as well.
AlAl
2006 Mobius LSV
-
04-25-2010, 10:13 AM #23
Al, great job and instructions, a how to top 10
09 21v LAUNCH
99 Outback LS. Sold
run your engine after you change your oil
68 th Member. WS420,HSE Revolution, OJ 466, Acme1157,1100 sacs,Kicker HLCD's n IX500.4, Supra Coolies
Doug
-
04-25-2010, 01:03 PM #24
Razz,
I am installing the same heating system, and was wondering how the helm vent was installed. Can you snap a pic so I can see where your's was installed?
Also you can get the "Y" from Go2Marine.com http://www.go2marine.com/product.do?no=74730F
They seem to have all the parts for these heaters.
Thanks,
Scott08 LSV, FAE, GIII upgraded to Johnson Reservable pumps, Evolution Cover, Flow.
-
04-25-2010, 06:17 PM #25Senior Member
- Join Date
- Jun 2008
- Location
- Eugene OR
- Posts
- 1,786
Al and MI-LSV. Thanks for the links. That will be very useful.
Al, Cannot wait to see how everything turned out today.2008 Outback V - Sold but never forgotten.
“Do not wait; the time will never be “just right.” Start where you stand, and work with whatever tools you may have at your command, and better tools will be found as you go along." -Napoleon Hill
-
04-26-2010, 02:48 AM #26
So my heater install is all done, got out to the lake today and everything works great. No leaks and the air blows nice and warm and there's plenty of cfm at all three vents. All in all, this was a fun and fairly straight forward project. There is a little bit of everything - electrical, plumbing, air ducts, and of course, drilling of big holes in the boat. None of it is very complicated so it's a good do it yourself project.
Thought I would post a few final pics of the install.
Here is the view under the dash. I had to relocate the PerfectPass module to make more room for the flex hose and I also zip tied a lot of the misc wires to get them out of the way of the tubes.
Here's a pic of the hoses going to the heater core. You can see the hose on the right that goes to the rear hot tube.
Instead of using the supplied switch, I used an existing three position switch on my dash. It was the ballast switch for the old Gravity I ballast system. When I had the dealer upgrade the ballast to the GIII system, they added three new switches under the throttle and left the original switch on the dash. So I ordered a heater faceplate from the dealer for $5 and replaced the ballast switch faceplate with it.
Here's a pic of the completed project.
Last edited by cab13367; 04-26-2010 at 02:57 AM.
Al
2006 Mobius LSV
-
04-26-2010, 02:51 AM #27
And here's a pic of my family enjoying the fruit of my labor today Air temp was in the mid-60's with water temp at 55 so the heaters definitely came in handy. The kids liked crawling under the bow cover with a heater vent while under way. Kept in nice and toasty in there.
Al
2006 Mobius LSV
-
04-26-2010, 11:44 AM #28
Looks real good Al. Was nice meeting the rest of your family and hanging out with you.
We had a great time yesterday and it was great seeing people on the water we knew lol.
Air temp would have felt a lot better if the sun was out but the water wasnt to bad. Al can attest i trunked it yesterday swimming and surfing. 56 is no thang but a chilly thang.Malo <--- Means--Evil or Mean One. This explains a lot.
2013 Mojo 2.5 Skylon Tower. Bestia < Beast >
[COLOR="#696969"]
-
04-26-2010, 03:38 PM #29
Al:
The install looks awesome! I am jealous and I may have to follow suit! People like you on this forum always get me wanting to do things to my boat. Mike helped me through the jitters of installing a set of Wetsounds on my tower last summer. This year may be the time to put in the heater. At that total cost, sweat equity comes cheap!
Mike:
If you jumped in 54 degree water with just swim trunks, my hat's off to you. How was the shrinkage???? LOL!2007 LSV - All red
Wetsounds PRO 80's WS420 Eq
Acme 1433
-
04-26-2010, 05:13 PM #30
Well as i told Claudia when she asked me the same thing, i said some thing shrink and some things pucker.
Surprisingly i got in at first because i needed to drain the coffee, and 2 bottles of water i drank, the water was so cold i couldn't though LOL. i normally don't wear a vest unless i board because ive been swimming my whole life but a vest in that cold of water does help you stay warmer.Malo <--- Means--Evil or Mean One. This explains a lot.
2013 Mojo 2.5 Skylon Tower. Bestia < Beast >
[COLOR="#696969"]