Results 31 to 40 of 64
Thread: Finished the Ballast... I think.
-
03-09-2009, 09:54 AM #31
Newty, I got out on the lake this sunday to do some surfing and one thing i found out, All the valves need to be the same size, i have one 1" and two 3/4" valve on it right now. What would happen is the 1" valve would open if i was using one of the smaller valves to fill a bag up. At this point i think im going to make a run the the home depot and get 2 more 1" valves.
Do you think the thru hull can handle haveing 2 800gph pumps? works out to 26.6 gpm. I remember you wrote somthing about gpm flow thru 3/4 pipeing but i cant find that now.Last edited by moombadaze; 03-09-2009 at 09:59 AM.
Hey, Its Moomba time
Its all about the dash - enjoy the dash, as that is your time between the dates
13 Mobius LSV-sold
08 Mobius LSV-sold
03 Mobius LSV-sold
life is about finding the balance between being a responsible adult and staying young at heart
-
03-09-2009, 10:06 AM #32
what is causing the 1" to open when other valves are open? I would think it wouldn't matter?
'06 Supra Launch 20SSV-gone but never forgotten
-
03-09-2009, 10:22 AM #33Hey, Its Moomba time
Its all about the dash - enjoy the dash, as that is your time between the dates
13 Mobius LSV-sold
08 Mobius LSV-sold
03 Mobius LSV-sold
life is about finding the balance between being a responsible adult and staying young at heart
-
03-09-2009, 11:03 AM #34Senior Member
- Join Date
- Feb 2005
- Location
- Ottawa, Ontario, Canada
- Posts
- 718
Maybe lighter springs can be had, rather than going springless?
-
03-09-2009, 06:29 PM #35Hey, Its Moomba time
Its all about the dash - enjoy the dash, as that is your time between the dates
13 Mobius LSV-sold
08 Mobius LSV-sold
03 Mobius LSV-sold
life is about finding the balance between being a responsible adult and staying young at heart
-
03-09-2009, 06:57 PM #36
I think the flow at the pressure of the pump will not make much difference for the 3/4 or 1" valve. did you notice an increase flow in the 1" valve?
i wish you guys would get this figured out so i can know what change to make and what will work. is there anything to that guys comment on wakeworld about unwanted flows, or what ever his concern was?Last edited by yearround; 03-09-2009 at 06:59 PM.
-
03-09-2009, 08:56 PM #37
nice clean jod aaa
-
03-09-2009, 11:17 PM #38
3/4 should be good for up to 30gpm with a very short run. Like what I have. There is less resistance with the 1 inch, is all I can think of that would cause the 1 to leak by.
My original thought on the valves when I first pulled them apart was to cut the spring down a little to see if it would work when I found the no spring thing.
-
03-10-2009, 01:43 PM #39Senior Member
- Join Date
- Feb 2005
- Location
- Ottawa, Ontario, Canada
- Posts
- 718
-
03-10-2009, 02:03 PM #40
thought about this in the am. keeping in mind that irrigation systems have 40-60psi at the entry end of the valve all the time, perhaps the spring is there to keep the system shut until the valve is energized and then it opens. in our system, the valve wouldn't open due to the low water pressure with the pump off, but as soon as you start filling, pressure is there, and no spring to keep it shut? since the valves in a typical irrigation system do not have power constantly, only when opened, something must be there to counteract the force of the water pressure at the entry.
thoughts on that?'06 Supra Launch 20SSV-gone but never forgotten