Results 1 to 10 of 20
Thread: Pop up Cleats?
-
04-21-2011, 12:27 PM #1
Pop up Cleats?
Was wondering if any of you have added pop up cleats to your boat? My boat doesn't have them so I was thinking about adding them. I don't think they'd be that difficult to install. What do you all think?
SOLD! 2011 Mobius LSV 325HP EFI
Digital Cruise Pro, Wakeplate, Kenwood KM550U and KCA-RC107MR x2, Kicker ZXM700.5, Kicker 6.5 Cabins, 10'' Kicker CompVT sub, Wetsounds SYN 4, Wetsounds REV10s, Wetsounds WS420Q, Gravity VI Surf Ballast, Acme 537
Board: '12 LF Harley (Monster) 139
Her Board: '11 Ronix Krush 128
Kids Board: '13 Ronix Vision 120
Skate: LF Faction 44
Surf: LF Custom Quad & XXX
Tow Rig:
2011 Toyota Tundra CrewMax TRD Magnetic Grey
3/1 Truxx Lift, and some other stuff...
-
04-21-2011, 12:36 PM #2
I've done them on other boats. Very easy!!! depending on which ones you buy you'll need a hole saw and maybe a small cut off wheel or jig saw. Oh... and a lot of painters tape.
Check Harbor Freight. they have them on the shelf here for <$10 a piece. They are decent quality too!
PWI as usual...
-
04-21-2011, 12:39 PM #3
I installed 4 of them on my Outback. The hardest part was figuring out where to put them. I opted for slightly different from the standard front locations. I bought the wrong kind though and it made the install much harder. I had to drill holes and then cut a slit between a couple of them for the cleat to slide all the way down. Take a close look at what you are buying. You only want to drill, not saw, if you can help it. But, overall not a bad job. Just be sure to measure 10 times and cut once (or something like that).
Did a little looking:
https://forum.moomba.com/showthread.php?t=5834Last edited by kaneboats; 04-21-2011 at 12:47 PM.
My Mom said I'm not allowed to get wet!
2008 LSV (sold)
2000 Outback LS (sold)
LLTR!!!!!!!!
-
04-24-2011, 03:31 PM #4
As usual, I took a different route and used these.
Kraig - 2010 Outback V
-
04-24-2011, 04:09 PM #5Senior Member
- Join Date
- Sep 2010
- Location
- Lighthouse Point, FL
- Posts
- 211
You might want to look at the "push pin" style cleats. They a very similat to the ones KSmith has. All you need to do to install them is drill a hole. Very simple and low profile
ToddREALLY????
-
04-24-2011, 05:39 PM #6
Cool ...... where'd u get em?
2007 Moomba Outback - going, going, GONE
2015 "NOT A MOOMBA"
Why Not? Play Hard! Get wet
-
04-25-2011, 08:10 AM #7
-
04-25-2011, 04:03 PM #8SOLD! 2011 Mobius LSV 325HP EFI
Digital Cruise Pro, Wakeplate, Kenwood KM550U and KCA-RC107MR x2, Kicker ZXM700.5, Kicker 6.5 Cabins, 10'' Kicker CompVT sub, Wetsounds SYN 4, Wetsounds REV10s, Wetsounds WS420Q, Gravity VI Surf Ballast, Acme 537
Board: '12 LF Harley (Monster) 139
Her Board: '11 Ronix Krush 128
Kids Board: '13 Ronix Vision 120
Skate: LF Faction 44
Surf: LF Custom Quad & XXX
Tow Rig:
2011 Toyota Tundra CrewMax TRD Magnetic Grey
3/1 Truxx Lift, and some other stuff...
-
04-25-2011, 05:56 PM #9
-
04-26-2011, 05:19 PM #10-Mark
2005 LSV
Tow w/: Volkswagen Touareg V8
Mods: Stereo, Stainless Cup Holders and Thru Hulls, Chrome Steering Wheel, EZ Nets, Moomba Etched Cleats
"Be more concerned with your character than your reputation, bc your character is what you really are, while your reputation is merely what others think you are."
-John Wooden