Wireless Phone Charger

[larry_arizona]

Mine would definitely overheat. I now have 5% window tint and it would probably be fine however gotta admit I could see the Supra one being way more useful do to you don’t have to remove the phone from the charger to use and it should hold it there instead of jumping around

The Supra layout is well done, the phone looks like a 3rd screen. You can also bypass the charger by moving the phone up about an inch.

The charger when active, does add heat to the phone.


Sent from my iPhone using Tapatalk

[parrothd]

Whatever engineer thought the Moomba location was a good spot should be tarred and feathered.

Sent from my Note9 using Tapatalk

The same fool that came up with this on the Craz, I think it's for kids sized cell phone or and 2000s sized Iphone..lol

20210515_113836 (1)_adobespark.jpg

[Zog]

The same fool that came up with this on the Craz, I think it's for kids sized cell phone or and 2000s sized Iphone..lol

20210515_113836 (1)_adobespark.jpg

Yeah, I hate that thing. I always think I can cram my phone in there and it winds up on the floor about 15 seconds later. Worse yet, is on our 2016 Moomba, there is a cubby adjacent to the cupholders that goes back behind the side panel. Put your phone in the cupholder or on the block there and it is likely to fall into the cubby. I lost my phone back there but was able to find it thanks to my apple watch. My sister-in-law had hers slip back there while we were at Lake Powell and thought she had just left it in the car. Didn't find it for another 2 weeks.

[RC_Hinojosa]

The same fool that came up with this on the Craz, I think it's for kids sized cell phone or and 2000s sized Iphone..lol

20210515_113836 (1)_adobespark.jpg

Agreed, that was the most useless cubby on my Craz that I NEVER used.

Sent from my Note9 using Tapatalk

[bealaddison]

The same fool that came up with this on the Craz, I think it's for kids sized cell phone or and 2000s sized Iphone..lol

20210515_113836 (1)_adobespark.jpg

Anyone making an upgraded compartment for this?


Sent from my iPhone using Tapatalk

[parrothd]

Anyone making an upgraded compartment for this?


Sent from my iPhone using Tapatalk

I 3d printed a peice that fills the hole, I have a switch there now. The cubby is in a bad spot and seems kinda limited what you can do with it.

[bealaddison]

I 3d printed a peice that fills the hole, I have a switch there now. The cubby is in a bad spot and seems kinda limited what you can do with it.

Bummer…was hoping someone had attempted it.


Sent from my iPhone using Tapatalk

[bealaddison]

Was looking around and found this one. It has much better reviews, holds the phone secure, and is angled to keep phone out of direct sun.

Scanstrut SC-CW-05E Rokk Wireless Edge https://www.amazon.com/dp/B081P2QYDS...VMHYH44WM17SAP





Sent from my iPhone using Tapatalk

[Holdmybeer]

I see they make a flat version also.
Not sure if you have the switch in the cubby, but I don't. Could replace that pointless piece with flat ABS plastic and then mount the charger there. Out of the sun, close to the radio for BT.

[bealaddison]

I see they make a flat version also.
Not sure if you have the switch in the cubby, but I don't. Could replace that pointless piece with flat ABS plastic and then mount the charger there. Out of the sun, close to the radio for BT.

That’s my plan, to incorporate some sort of a mount in the cubby next to the radio. I like the angle on this one for visibility.


Sent from my iPhone using Tapatalk