Results 21 to 30 of 34
-
07-22-2020, 11:16 AM #21Junior Member
- Join Date
- Jul 2020
- Posts
- 4
Going to do the same thing
I'm getting ready to do the exact same thing. I purchased 2 speakers and brackets from someone upgrading to wetsounds. They will match my existing 2 speakers perfectly. So what do i have to do about wiring? The amphenol connectors are there in the tower. What wiring is required on the other end?
Would greatly appreciate your help! Thank you!
-
07-22-2020, 12:59 PM #22
Adding 2nd set of JL 8.8’s to FX one tower.
If you have factory speakers it’s much easier.
The Factory plugs at the speaker side should be plug n play.
Climb into the starboard dog house and find the speaker plugs. I had to clip a few zip ties and you should get enough slack to work on them comfortably.
Then it’s a matter of running two left side wires and two right side wires and attaching to your new amp.
Did you get a JL 800/8 amp to run your 4 towers?
Sent from my iPhone using Tapatalk2021 Supra SA 400
2018 Supra SA 400 (SOLD)
Michigan
-
07-23-2020, 09:38 AM #23
Great topic. I've been thinking about this upgrade in the future, maybe next year. Just planning on cost. The instructions you all provided seem pretty clear, straightforward, even for someone who has never done this before, like me. So this is great info.
Quest:
the speakers you added do not have the down firing LED lights. I found these at Crutchfield:
https://www.crutchfield.com/S-9S12cS...yABEgLESvD_BwE
Is this what u used? Did u find the ones with the integrated down firing LED's anywhere.?
The brackets in these speakers are round, I'm guessing I can remove them and install the angle brackets u mentioned, or did u get a diff speaker altogether.?
The amp I found is this:
https://www.crutchfield.com/S-KX7BFI...iABEgLE6vD_BwE
So I'm guessing a total cost of <2400$, including the aftermarket angle brackets.
Does this all sound about right?
Unlike the Moomba, I plan to keep this boat for a looong time. (Under spousal threat). So I bought it with plans of slowly adding DIY upgrades over time. Things such as this, a second set of racks, prop, Phender Pro's, et. al.2020 Supra SL 400
2015 Moomba Mojo(Sold)
2018 Yamaha Waverunner(Just to fool around)
2018 F150 Lariat
sport edition, 3.5lt ecoboost
-
07-23-2020, 10:21 AM #24
Adding 2nd set of JL 8.8’s to FX one tower.
You can use the aftermarket JL 8.8’s with the JL tube clamps. It takes some additional work but I actually like the look of the finished product. I personally like the center set being slightly offset. Gives it some depth.
You can also add the JL downfiring LED tail cones to match the factory ones. You order them right from JL website. I think I got them on sale for $150
You can also buy the Supra specific version of the JL 8.8’s, it’s the only way to get the factory speaker mount. They are $$$ but are truly plug and play.
As far as the amp, your 2020 has the newer JL
mvi amps, the 800/8i is around $1200
Sent from my iPhone using TapatalkLast edited by larry_arizona; 07-23-2020 at 10:23 AM.
2021 Supra SA 400
2018 Supra SA 400 (SOLD)
Michigan
-
07-23-2020, 04:56 PM #25
For the cost, an amp like the Wet Sounds Syn-DX2 or the Kicker KXMA1200.2 are far better then M series 8 chnl bridged into 4. WAY too many RCA splitters required to make it work correctly. The Syn-DX2 is going to deliver similar wattage and only require a single pair of RCA. The KXMA1200.2 is going to also only require a single pair of RCA and yield a ton of wattage head room.
-
07-23-2020, 05:46 PM #26
holy paycheck batman...... $1200+ for that JL amp is insane.
'06 Supra Launch 20SSV-gone but never forgotten
-
07-23-2020, 07:06 PM #27
Adding 2nd set of JL 8.8’s to FX one tower.
When I added the 800/8 in place of the 400/4 like the factory does it, it still only uses 4 RCA plugs total, wether you have 2 or 4 tower speakers, the tower is one zone.
I think you only need one JL mvi amp to take advantage of the mvi “tun” features
Right or wrong, I wanted my system to be like the factory set up.
Sent from my iPhone using Tapatalk2021 Supra SA 400
2018 Supra SA 400 (SOLD)
Michigan
-
07-23-2020, 07:53 PM #28
If you populated 4 RCA on an M800/8 bridged in 4 chnl mode and its one volume zone, then there is an RCA split somewhere. To make the most of the M800/8 in 4 chnl mode to 4 full-range speakers, you have to populate all 8 RCA inputs. JL's own engineers state this, its in the amps manual as well. This is also common with bridging many other full-range amps.
I have not dove too deep into the mvi amps, but I believe the DSP function allows you to overcome the input/bridging conundrum you have with the M series amps.
-
07-23-2020, 08:20 PM #29
-
07-29-2020, 09:36 AM #30Junior Member
- Join Date
- Jul 2020
- Posts
- 4
Wiring Question