Results 91 to 100 of 180
Thread: '17 Craz Audio Questions.
-
03-11-2017, 03:00 PM #91
Do you know what gauge the speaker wire is. I'm sure it's 16ga as that's all the info I'm seeing online. Everyone keeps saying for the REV10 you should use at least 14 even better would be 12. Wanting to do things right the first time is it worth the trouble to upgrade the wiring. I'm sure it's not hard, just tape the new wire to the old and pull the old wire.
2008 LSV on the way out
'17 CRAZ!!! on the way in
-
03-11-2017, 03:27 PM #92
-
03-11-2017, 03:38 PM #93
'17 Craz Audio Questions.
Wires looked like 16ga
Sent from my iPhone using Tapatalk2017 Moomba Craz
-
03-11-2017, 04:19 PM #94
-
03-14-2017, 10:07 AM #95
Hey guys,
I emailed Roswell and asked them to send me the wiring diagram for the A3 aviator tower on all of the new 2017 Moombas.
I'm pretty sure that some of you guys were thinking I was talking out of my butt when I said there were extra wires for the speakers, in this new A3 version, and this picture that I am attaching confirms it.
Perhaps the moderators want to save this picture in the archives for future use for other people that end up with the A3 tower.
Sent from my iPad using Tapatalk2017 Moomba Craz
-
03-14-2017, 10:12 AM #96
Looks good. Will add to a sticky info thread.
My Mom said I'm not allowed to get wet!
2008 LSV (sold)
2000 Outback LS (sold)
LLTR!!!!!!!!
-
03-15-2017, 12:51 PM #97
-
03-15-2017, 02:12 PM #98
https://www.amazon.com/Stinger-SVMR-...+voltage+meter
They also have blue ones.2016 Moomba Mojo
2006 Supra 24SSV - Traded
-
03-16-2017, 01:54 PM #99
Ok guys, I've been looking at distribution blocks, in line fuse holders, circuit breakers, power cables, ground cables, Perkos, AND ON AND ON AND ON......
Think I might be overthinking things for my application. I came across the pic online that shows the stock amp board from a 2016 Craz with the bow speaker amp upgrade( same as I getting, probably.) I looks like the Kicker amp is getting power from a stock distribution block with a 8ga wire and inline fuse.
Question: Can I run my SNY-4 from that block using a 4ga and inline fuse?
Sure would simply my setup and save on rewiring everything until I decide to put the second battery and third amp with sub in.
2008 LSV on the way out
'17 CRAZ!!! on the way in
-
03-16-2017, 03:54 PM #100Senior Member
- Join Date
- Oct 2016
- Location
- Tims Ford Lake TN
- Posts
- 453
I'm going to piggyback on this latest post......so I think I have same distro block and wiring to the factory KX200.2 in my Mojo. My current change to Exile 30.2 (tower) and Javelin (cabin + sub) calls for 4 AWG wire for hot and ground. If Rak is correct that the factory is 8 AWG, looks like I need all new. Can I power off of that distro block with no issues? IS the supply wires to the distro block from battery / perko sufficient?
2016 Mojo Surf
Raptor 400
1100 rear bags / 500 IBS / 600 LeadWake
Exile amps/tower - Kicker in-boat
FAE