Got my new ZLD in and wanted to give my thoughts, likes, dislikes on it.

First, like all Exile products shipping was fast,

If you never owned a ZLD then this next section won't matter, but owning one and having it pre mounted this next section is interesting.

First having the original one mounted, I was thinking hey Plug and Play, swap RCA's swap power ground remote block, unscrew a couple screws and I'm done.

yea not so much...

First the Case is designed slightly different, the side mounts are wider apart, also the new brackets don't allow a back and forth slide adjustment to make it easier to flush mount it. The holes are drilled and no adjustment is available.

Second the new power plug is much smaller then version 1, power, remote, ground are the same location but you must change the wires over. Also the new block has really small jewelers flat head screws, not the same size as the old one. This caused me to have to get a second screw driver as my normal one to tune the amps was too big.

Third is the nomenclature on the new ZLD is different. It is listed as Cabin, Tower, Sub due to the true zone control it has, when changing RCA's I had to guess which is my cabin and tower, old ZLD said Front, Rear, Sub.

I set the Main and AUX gains on the ZLD to 90% as recommended by Exile.
I have not turned my Amp gains down yet as I am going to get the system re-tuned anyhow.

After getting these thing changed, I used the old brackets that are adjustable to allow it a flush mount where mine is mounted under the dash.

On to the unit's functionality.

Main Volume dial is large and easy to use, I don't like that there is no DOT or Hash, or bevel to allow me to easily see what volume level I am at. I will need to paint a Dot or something to know the volume. I like to use 3 settings basically, low, 1/2 and 3/4 are my main volume points and with no markings I was constantly going to 0 then back up.

Cabin, Tower, and Sub are true separate volume controls now. You can turn each zone off, turn one up louder then the other or lower. This is all dependent on the main volume of course.

For me I don't mess with my Cabin level. I set it to 75% and then use the main Volume knob.

I personally use the Tower volume the second most, I don't like that its next to the main volume because it's a pretty small dial. i would have been happier is they mounted it farther away in the Sub position. I also use my Sub volume a lot to make sure I don't over drive the sub on heavy bass tracks, also sometimes the music has so much base everything is vibrating off the dash, such as my phone lol.

Once I got used to the new volume locations for my tower and Sub everything was ok.

Sound,

When I first fired it up the biggest thing I noticed was my Sub was really pounding now. It has always pounded but not at 25% volume. So I know I have to watch it now LOL.

Over all the sound quality is much better, best thing I noticed is no light noise from my tower. I have had this since we moved into the HLCD market, my wires are all good, gains are down, its just a noise I have always had when nothing is playing. its very feint and most don't notice it, but I do lol.

Also now when i turn the unit off I don't get this annoying Bass thump. It was due to the ZLD being an instant off and sending a signal or something to my sub amp and making it thump.

Old Exile amps used to do this too, Exile went back and installed a resister on the shut down side of the amp to stop this noise, I assume the first gen ZLD didn't have this slow power down function and the new one does.

Though out the day yesterday the stereo was loud as normal, a couple times we got to loud and caused the towers to pop a little, and then we had to turn it down some, this is due to the amp gains not being turned down enough. I want to say my amp gains are about 20% right now, so going to have to go to 105 or even 5%.

Overall though I think Exile did a great job on the new MK II ZLD.
Talking to them they are already working on notching the main volume, and making the brackets with a slide adjustment.

Few pics of the Old, and the changes with the new, also a pic how mine is mounted because another Mojo owners was curious. I didn't snap a pic of the new installed because its the same as the old position.

Mounting location



Mounted right unto the fiberglass with screws. Its thick enough for the screws to bite, never has loosened up.



New ZLD bottom side.