Results 11 to 20 of 22
-
07-09-2012, 12:05 PM #11Senior Member
- Join Date
- Jun 2007
- Posts
- 883
soldering isn't that bad, it's just being able to do it in the storage below the radio...
2006 Moomba Mobius LSV
Stereo: Kenwood KMR-D562BT
Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"[/SIZE]
-
07-09-2012, 02:39 PM #12
I installed my 550u in less than 15 minutes. It really isn't as difficult as it is being made out to be.
Wire the new harness up to your existing power, speaker, and remote wires, then put your radio in and plug the harness into the new radio. Voila...install complete.
Sent from my iPhone using TapatalkSOLD! 2011 Mobius LSV 325HP EFI
Digital Cruise Pro, Wakeplate, Kenwood KM550U and KCA-RC107MR x2, Kicker ZXM700.5, Kicker 6.5 Cabins, 10'' Kicker CompVT sub, Wetsounds SYN 4, Wetsounds REV10s, Wetsounds WS420Q, Gravity VI Surf Ballast, Acme 537
Board: '12 LF Harley (Monster) 139
Her Board: '11 Ronix Krush 128
Kids Board: '13 Ronix Vision 120
Skate: LF Faction 44
Surf: LF Custom Quad & XXX
Tow Rig:
2011 Toyota Tundra CrewMax TRD Magnetic Grey
3/1 Truxx Lift, and some other stuff...
-
07-09-2012, 02:41 PM #13Senior Member
- Join Date
- Jun 2007
- Posts
- 883
2006 Moomba Mobius LSV
Stereo: Kenwood KMR-D562BT
Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"[/SIZE]
-
07-09-2012, 07:17 PM #14
No, I used crimp caps. It's pretty easy just slide lay on your back and then crawl head first in your observers compartment and it's right there. Space is tight but it's not difficult.
Sent from my iPhone using TapatalkSOLD! 2011 Mobius LSV 325HP EFI
Digital Cruise Pro, Wakeplate, Kenwood KM550U and KCA-RC107MR x2, Kicker ZXM700.5, Kicker 6.5 Cabins, 10'' Kicker CompVT sub, Wetsounds SYN 4, Wetsounds REV10s, Wetsounds WS420Q, Gravity VI Surf Ballast, Acme 537
Board: '12 LF Harley (Monster) 139
Her Board: '11 Ronix Krush 128
Kids Board: '13 Ronix Vision 120
Skate: LF Faction 44
Surf: LF Custom Quad & XXX
Tow Rig:
2011 Toyota Tundra CrewMax TRD Magnetic Grey
3/1 Truxx Lift, and some other stuff...
-
07-10-2012, 12:10 AM #15Senior Member
- Join Date
- Jun 2007
- Posts
- 883
-
07-10-2012, 07:21 AM #16Senior Member
- Join Date
- Aug 2008
- Location
- Hilliard, Ohio
- Posts
- 794
-
07-10-2012, 08:02 AM #17
That should work. I have two of the Kenwood KMR107 remotes. They are kinda spendy but they are so much nicer than those aeware remotes. I had those aewares in my old boat and had a few problems with them.
Sent from my iPhone using TapatalkSOLD! 2011 Mobius LSV 325HP EFI
Digital Cruise Pro, Wakeplate, Kenwood KM550U and KCA-RC107MR x2, Kicker ZXM700.5, Kicker 6.5 Cabins, 10'' Kicker CompVT sub, Wetsounds SYN 4, Wetsounds REV10s, Wetsounds WS420Q, Gravity VI Surf Ballast, Acme 537
Board: '12 LF Harley (Monster) 139
Her Board: '11 Ronix Krush 128
Kids Board: '13 Ronix Vision 120
Skate: LF Faction 44
Surf: LF Custom Quad & XXX
Tow Rig:
2011 Toyota Tundra CrewMax TRD Magnetic Grey
3/1 Truxx Lift, and some other stuff...
-
07-22-2012, 10:35 PM #18Senior Member
- Join Date
- Jun 2007
- Posts
- 883
2006 Moomba Mobius LSV
Stereo: Kenwood KMR-D562BT
Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"[/SIZE]
-
07-22-2012, 11:22 PM #19
It should....
A Day at the Lake...Priceless
A Day in Powder...Endless
Joe V
2012 Möbius XLV~ Loaded & Exiled
2007 Outback V ~ sold
-
07-22-2012, 11:50 PM #20Senior Member
- Join Date
- Jun 2007
- Posts
- 883
also, anyone know what that type of plug is called on the back of the old deck? maybe I can find the other matching end at radio shack so I can keep the wiring harness detachable.
2006 Moomba Mobius LSV
Stereo: Kenwood KMR-D562BT
Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"[/SIZE]