Results 11 to 20 of 20
Thread: ventalation leuvers
-
05-09-2009, 07:50 AM #11Member
- Join Date
- Aug 2007
- Location
- Lake Webster
- Posts
- 66
Glad to hear your windshield project turned out so well. It sounds like you got quite a deal. Could you post some pictures?
Also regarding your question on the louvers. I am not sure what you are asking. Are you asking about where they run under the floor? or along the vertical divider between the driver footwell and the storage compartment in front of the passenger seat? If it is in that storage area and not under the floor I could try to get some pics this weekend.
-
05-09-2009, 02:11 PM #12Junior Member
- Join Date
- Apr 2009
- Posts
- 18
louver hoses
If I remember correctly,(bad memory) the louver hoses went though the floor somewhere. Each louver has two 3" hoses that have a attachment ring with four screws on the loose end. So, they attach to a flat surface that has a 3" hole.(somewhere) If I stretch out the hoses to there maximun lenght they still won't reach the service cavity under the floor.(cables and wires from dash to motor) IMO that is where they would vent the engine compartment the best. Also rain water that gets into the louvers has to drain into the bilge area also. If I were to drill the 3" holes under the louvers(floor) they would'nt do anything but expose the sealed/air tight dry portion of the bilge to water. There is a possibility that one or more of these hoses go through the divider between the "ski storage area" and the cock pit area.( I also had to replace that to access floor underneath so if there where holes there, they no longer are.)
-
05-09-2009, 03:20 PM #13Junior Member
- Join Date
- Apr 2009
- Posts
- 18
near finish pics
These are some pics I took of it today. I found another thing to repair. The neighbors dog ate the speedo pickups and hoses. So I currently have the gas tank back out to access the transom. I'm still tring to get the pics of the floor replacement process.
-
05-10-2009, 08:54 PM #14Member
- Join Date
- Aug 2007
- Location
- Lake Webster
- Posts
- 66
My tubes run from the louvers, along the vertical divider and into the floor of the storage compartment. I honestly couldn't tell you where they go from there.
-
05-10-2009, 08:56 PM #15Member
- Join Date
- Aug 2007
- Location
- Lake Webster
- Posts
- 66
The windshield looks great btw.
-
05-25-2009, 08:21 PM #16Junior Member
- Join Date
- May 2009
- Posts
- 10
I need to take my rear panel out that covers the gas tank out, how does the panel come out?
-
05-25-2009, 08:39 PM #17Junior Member
- Join Date
- Apr 2009
- Posts
- 18
back seat panel
If you have a boomerang of a kanga its reallly easy.
1. Unsnap floor cushions.
2. Carfully remove screw covers for screws in backrest.(flat head screw driver)
3. Back out screws in back rest. (phillips)
4. Remove large head screws in the panel.(phillips)
5. Jocky it around and remove it.
Thats it.
What are you going after?
-
05-25-2009, 09:07 PM #18Junior Member
- Join Date
- May 2009
- Posts
- 10
I have the drivers side getting wet on the carpet under the rear cusions and I think that it is leaking where the swim platform mounts, it is always underwater and that is all that is underwater on that side. I am planning on taking the swim platform off and cleaning the mounting holes and reinstall with plenty of sealant.
-
05-25-2009, 10:04 PM #19Junior Member
- Join Date
- Apr 2009
- Posts
- 18
leak
It could also be the clam shells for the speedo hoses.Water could also be slashing under the cover for the rudder. Good luck, hope you find it.
-
05-25-2009, 10:20 PM #20Junior Member
- Join Date
- May 2009
- Posts
- 10
I am plannng on taking the rear panel & fuel tank out and taking it down to the boat ramp, it is only a mile from the house and I will back it down and wait to see what leaks. I will check everything and hopefully find the problem.