New Software Issues and Performance - 2022 Mojo

[duch17]

Could you not calibrate you boat with weight in you boat as long as it's sitting flat on the water?

Sent from my SM-G998W using Tapatalk

[Hayden]

Could you not calibrate you boat with weight in you boat as long as it's sitting flat on the water?

If you're referring to inclinometer calibration, any ballast weight (water/leadwake) is going to skew the numbers in my opinion. If you're referring to the draft sensor, I don't know and haven't seen Jon/Goose comment on that point.

[uniwarking]

Instructions for calibration of both sensors is in the display manual. The draft sensor will be very impacted by weight. The inclinometer zero calibration is the reference point for pitch and roll and is intended to be the boat sitting “flat.” I think it would be really hard to know if your boat was flat I’d you had a lot of gear/ballast/lead/people on board.


Sent from my iPhone using Tapatalk

[Ironcross25]

I was not impressed at 1st as well on my 22. There is a post on here that has pitch and roll setting for ext surf side. Great info. I have a small crew. My wife and 3 kids. 10 6 and 3. I run all ballast full and have 300 led in nose. I do not use auto wake. I use switches to fill bags and make sure they are full. Starboard surf inside 13.5 pitch and 7.5 roll and port surf I use 9.5 pitch and -3.5 roll. 11mph. I don’t really touch wake plate much at all. Wave is nice and clean and can surf it close up and far back for days. More people I get the bigger and even better the wave is. I plane to get more led but just haven’t yet but I’m happy now and it’s better than my 12 mojo. In the beginning like you my 12 was better but now the 22 takes it. It just takes time to play around with it.


Sent from my iPhone using Tapatalk

[duch17]

If I want disable autofill what should my trigger and trigger margin be set at

2019 mojo with new software

Should trigger be set really high(myguess)?

Sent from my SM-G998W using Tapatalk

[Hayden]

If I want disable autofill what should my trigger and trigger margin be set at

2019 mojo with new software

Should trigger be set really high(myguess)?

Sent from my SM-G998W using Tapatalk

Not sure what you are referring to here....do you mean "disable autowake" or do you mean "reset/customize ballast timers"? Both are done via the display under vessel settings.

[duch17]

Not sure what you are referring to here....do you mean "disable autowake" or do you mean "reset/customize ballast timers"? Both are done via the display under vessel settings.

Disable autofill on the development page, basically adjust the trigger point so it doesn't refill my ballasts.
I will be back in Invermere hopefully Friday and be able to adjust it again and try I out.

Sent from my SM-G998W using Tapatalk

[duch17]

Disable autofill on the development page, basically adjust the trigger point so it doesn't refill my ballasts.
I will be back in Invermere hopefully Friday and be able to adjust it again and try I out.

Sent from my SM-G998W using Tapatalk

20220705_150424.jpg
Picture of the setting page

[uniwarking]

20220705_150424.jpg
Picture of the setting page

I don’t think you need to get into the dealer development page and have them tinker with thresholds, the new SW has a smart tech menu that allows you to turn off the ballast auto fill if I recall correctly


Sent from my iPhone using Tapatalk

[Hayden]

What version of the software are you using? Did you need to use the dealer code to get to the development screen? I don't remember that screen being available, (I may have missed it).

My software version: MoombaBP_MY22_47740_20211206