Results 1 to 8 of 8
Thread: Surf plates
-
09-09-2018, 12:16 AM #1
Surf plates
Been having a fair amount of issues with the surf plates this year, when only surfing port really haven't had much trouble, but when trying to switch to goofy, all hell breaks loose and I get stuff like this. Took 10 minutes of toggling the switch back and forth , key on and off, battery on and off to get it back to normal, the surf switch is in surf starboard position in picture. And sitting still at idle. Every goofy side attempt has been similar to picture, or would say 80% port plate, but starboard plate was still fully deployed from regular surfing and port plate was still not deployed at all. Just an observation an minor nuisance.
Sent from my Pixel 2 using Tapatalk2017 Craz surf auto wake
1140 # rears wet sounds
-
09-09-2018, 07:56 AM #2
Sounds like a warranty claim to me
Sent from my iPhone using TapatalkDavid
2017 Moomba Mojo Max Surf Edition, 2 Pair Wetsounds Rev10s powered by an SD2, 6 pair Wetsounds XS650M and Wetsounds XS12 powered by SD6 all controlled by a WS420. 2 Lumitec SeaBlaze X2 Spectrum underwater lights
SOLD***2008 Mobius LSV, Gravity III , Wake Plate, Z5, Exile SX65c's, Exile XM9s, Exile XI12D, Exile Javelin, Exile 30.2***SOLD
-
09-16-2018, 09:12 PM #3
Doing some more playing out of the water, here are some pics of the starboard plate. No wonder I'm having such issues with the goofy wave. The first pic is surf starboard, you can see both plates deployed, second pic is is wake board , or both plates 0, last pic is after actually getting it to go to 0 position
But the only way to get the starboard side plate to actually go to 0 , I would have to manually set it to 0. Then if I set it back to my 60 % setting to surf port, after 3 cycles from wake to surf port on the switch, you can see that the plate doesn't fully retract back to 0.
So even though i flip the switch to middle position, the starboard plate stays at about 15% deployed, or of flipped to goofy, it is still deployed
Sent from my Pixel 2 using Tapatalk2017 Craz surf auto wake
1140 # rears wet sounds
-
09-16-2018, 10:11 PM #4
Damn that sucks man. Sounds like it just needs a reflash though.
2019 Supra SL450
-
09-16-2018, 10:17 PM #5
Re flash or new actuator, in the pic with both plates deployed, the starboard side reading was 0 like it's supposed to be, but E.T. still wouldn't go home
Sent from my Pixel 2 using Tapatalk2017 Craz surf auto wake
1140 # rears wet sounds
-
09-16-2018, 10:18 PM #6
You were able to get it to move, though, right? If so, it's not the actuator.
Is a reflash something a boat owner can do? I thought I read someone has done it.2019 Supra SL450
-
09-16-2018, 10:22 PM #7
It moves, but it seems like when adjusting it in the 5% increments, one bump you would hear move for a second, next bump you could hear move for 5 seconds,
Sent from my Pixel 2 using Tapatalk2017 Craz surf auto wake
1140 # rears wet sounds
-
09-16-2018, 10:26 PM #8
And the actuator would creep down, when it was actually at 0 , I would deploy it to 60 , return it, deploy return, every cycle it would not fully return by about 5%
Sent from my Pixel 2 using Tapatalk2017 Craz surf auto wake
1140 # rears wet sounds