Results 1 to 10 of 10
Thread: Ballast timer issues
-
07-15-2013, 01:05 PM #1
Ballast timer issues
The last few times we've been out I've had some problems with the ballast timers. I have the rears set to 11 mins and the front set to 930. The front pump fills both the center and the IBS.
The problem that I am having is I can fill up all the bags that I need to fine and the levels will reach whatever they need to be whether it be 100% 75% or whatever. We'll surf or whatever and then when I look at the fill levels they'll be registering much less than they were previously and no water has been drained and the pumps haven't been on. Yesterday for example the left pump was 92% the front was about 66% and the right was 36%. Went to drain them and the right pump drained fine but half way through the front and left stopped and registered 0% when there was easily 50-75% still left in the bags. I had to drain them (1100 and 400#s) in 30 sec increments. Has anyone ever had this problem before or know of a resolution?SOLD! 2011 Mobius LSV 325HP EFI
Digital Cruise Pro, Wakeplate, Kenwood KM550U and KCA-RC107MR x2, Kicker ZXM700.5, Kicker 6.5 Cabins, 10'' Kicker CompVT sub, Wetsounds SYN 4, Wetsounds REV10s, Wetsounds WS420Q, Gravity VI Surf Ballast, Acme 537
Board: '12 LF Harley (Monster) 139
Her Board: '11 Ronix Krush 128
Kids Board: '13 Ronix Vision 120
Skate: LF Faction 44
Surf: LF Custom Quad & XXX
Tow Rig:
2011 Toyota Tundra CrewMax TRD Magnetic Grey
3/1 Truxx Lift, and some other stuff...
-
07-15-2013, 01:23 PM #2
sounds like something is off with the control module. you didn't get it wet, did you?
-
07-15-2013, 10:25 PM #3
Ballast timer issues
SOLD! 2011 Mobius LSV 325HP EFI
Digital Cruise Pro, Wakeplate, Kenwood KM550U and KCA-RC107MR x2, Kicker ZXM700.5, Kicker 6.5 Cabins, 10'' Kicker CompVT sub, Wetsounds SYN 4, Wetsounds REV10s, Wetsounds WS420Q, Gravity VI Surf Ballast, Acme 537
Board: '12 LF Harley (Monster) 139
Her Board: '11 Ronix Krush 128
Kids Board: '13 Ronix Vision 120
Skate: LF Faction 44
Surf: LF Custom Quad & XXX
Tow Rig:
2011 Toyota Tundra CrewMax TRD Magnetic Grey
3/1 Truxx Lift, and some other stuff...
-
07-16-2013, 06:03 AM #4
Ballast timer issues
Yes, I'm kidding. I've asked SC to respond to this one.
-
07-16-2013, 10:36 AM #5
E4Nash,
I forgot to say something about this when we were talking yesterday. Try doing a hard reset on your ballast PDM. Disconnect both the power and ground from the PDM and let it sit for about 10 minutes, then reconnect. Hopefully this fixes your issues. If not, send me an email.
-
07-16-2013, 11:43 AM #6
Ballast timer issues
Thanks Jon will do...now where is the PDM for the ballast located in my boat?
SOLD! 2011 Mobius LSV 325HP EFI
Digital Cruise Pro, Wakeplate, Kenwood KM550U and KCA-RC107MR x2, Kicker ZXM700.5, Kicker 6.5 Cabins, 10'' Kicker CompVT sub, Wetsounds SYN 4, Wetsounds REV10s, Wetsounds WS420Q, Gravity VI Surf Ballast, Acme 537
Board: '12 LF Harley (Monster) 139
Her Board: '11 Ronix Krush 128
Kids Board: '13 Ronix Vision 120
Skate: LF Faction 44
Surf: LF Custom Quad & XXX
Tow Rig:
2011 Toyota Tundra CrewMax TRD Magnetic Grey
3/1 Truxx Lift, and some other stuff...
-
07-16-2013, 01:08 PM #7
Port side rear locker. Pumps and Pdm are mounted on a board behind the carpeted panel towards the transom.
-
07-16-2013, 04:40 PM #8
Ballast timer issues
SOLD! 2011 Mobius LSV 325HP EFI
Digital Cruise Pro, Wakeplate, Kenwood KM550U and KCA-RC107MR x2, Kicker ZXM700.5, Kicker 6.5 Cabins, 10'' Kicker CompVT sub, Wetsounds SYN 4, Wetsounds REV10s, Wetsounds WS420Q, Gravity VI Surf Ballast, Acme 537
Board: '12 LF Harley (Monster) 139
Her Board: '11 Ronix Krush 128
Kids Board: '13 Ronix Vision 120
Skate: LF Faction 44
Surf: LF Custom Quad & XXX
Tow Rig:
2011 Toyota Tundra CrewMax TRD Magnetic Grey
3/1 Truxx Lift, and some other stuff...
-
07-22-2013, 11:48 PM #9
Is the hard reset working for you guys?
I get the pumps cutting out on both fill and drain. I also have the pumps not filling OR draining in accordance with the % on the screen (when they don't cut out). I went to fill the center tank once and at 10% it was coming out the vent.... once, while on the lift and gauge at 0%, I hit drain and listened to water spill out for a few minutes..
If the hard reset is working i will give it a try,but where is it on the 2012 Mojo? (Why wouldn't it reset each time i switch my batteries to the off position?)
Thanks,2012 Mojo2.5
Ballast:
1100 surf side
400 goofy side
500 under floor
725 IBS
260 bow floor
(The more spotters the better)
Acme1235
-
07-23-2013, 05:05 AM #10
Ballast timer issues
I haven't been able to do the reset yet...was going to do it this past Saturday but work got in the way. Hopefully I'll get to it this week sometime.
SOLD! 2011 Mobius LSV 325HP EFI
Digital Cruise Pro, Wakeplate, Kenwood KM550U and KCA-RC107MR x2, Kicker ZXM700.5, Kicker 6.5 Cabins, 10'' Kicker CompVT sub, Wetsounds SYN 4, Wetsounds REV10s, Wetsounds WS420Q, Gravity VI Surf Ballast, Acme 537
Board: '12 LF Harley (Monster) 139
Her Board: '11 Ronix Krush 128
Kids Board: '13 Ronix Vision 120
Skate: LF Faction 44
Surf: LF Custom Quad & XXX
Tow Rig:
2011 Toyota Tundra CrewMax TRD Magnetic Grey
3/1 Truxx Lift, and some other stuff...