Results 121 to 130 of 197
Thread: Mojo Surf Ballast Setup
-
07-11-2013, 01:08 PM #121Member
- Join Date
- Jun 2013
- Posts
- 30
Hi, just installed the new ballast today. For the 1" TH I have to enlarge the stock holes (didn't take tool to do it). We tested (only 1 driving and 1 surfing). Speed was 15km/h (9.4 mph) max otherwise the wave become dirty. Wakeplate 3/4 up. Starboard ballast 20%. How much did you put in your starboard ballast when wakesurfing ? Did you fill 100% the IBS ? The lake today was not flat at all so maybe it's not the best to test. We will test again tomorrow with more people onboard. About the propeller, did you change it?, it seems the boat as much more difficulties to move all that weight compare to stock ballast !
Timer setting (aprox) Left 13min (1100+370), Center 11 min (stock + IBS) & Right 11min (1100)
Thanks for feedbacks
p.s : my hands are ruined with these damned hose !! even with heatgun !! Especially the "Y" connection !Last edited by gurt; 07-11-2013 at 01:10 PM.
2012 Moomba Mojo 2.5
2x1100lbs, 370lbs, center hard tank+IBS
ACME 1235 prop
Wakeboard Hyperlite Belmont
Wakeskate Hyperlite Byerly
Wakesurf Hyperlite Broadcast 5.4
-
07-11-2013, 01:19 PM #122
gurt, I surf with port locker 1,100 full, 370 port full, center full, IBS full and starboard locker 1,100 about 25-50% and @ 11.1 mph with the wakeplate anywhere from 1/4 to full up. The wind and water conditions can impact the wave, but I'm normally able to clean it up pretty easy. I upgraded the prop from the factory and have the 345 hp motor & have no issues at all getting moving.
-
07-11-2013, 03:09 PM #123
Mojo Surf Ballast Setup
SOLD! 2011 Mobius LSV 325HP EFI
Digital Cruise Pro, Wakeplate, Kenwood KM550U and KCA-RC107MR x2, Kicker ZXM700.5, Kicker 6.5 Cabins, 10'' Kicker CompVT sub, Wetsounds SYN 4, Wetsounds REV10s, Wetsounds WS420Q, Gravity VI Surf Ballast, Acme 537
Board: '12 LF Harley (Monster) 139
Her Board: '11 Ronix Krush 128
Kids Board: '13 Ronix Vision 120
Skate: LF Faction 44
Surf: LF Custom Quad & XXX
Tow Rig:
2011 Toyota Tundra CrewMax TRD Magnetic Grey
3/1 Truxx Lift, and some other stuff...
-
07-11-2013, 03:22 PM #124
-
07-11-2013, 08:59 PM #125
I used the upgraded clear tubing with the black plastic embedded. I place the end of the tubing in boiling water for 30-45 secs and it becomes very flexible and slides over connections with minimal difficultly.
2012 Mojo
2009 LS (SOLD!!!)
2010 Tundra 5.7 Crewmax 4X4
-
07-11-2013, 11:34 PM #126Member
- Join Date
- Jun 2013
- Posts
- 30
Hello Wolfman, thks for infos. So your prop comes from moomba? I saw some prop from wakeprop.com
Did you remember the model that you have? thx
I don't have issue but it looks that an other prop would be better..2012 Moomba Mojo 2.5
2x1100lbs, 370lbs, center hard tank+IBS
ACME 1235 prop
Wakeboard Hyperlite Belmont
Wakeskate Hyperlite Byerly
Wakesurf Hyperlite Broadcast 5.4
-
07-12-2013, 12:15 AM #127Member
- Join Date
- Jun 2013
- Posts
- 30
after replacing the prop, did you have to calibrate something because speed at same rpm change or is there a sensor that doesn't depend from prop?
2012 Moomba Mojo 2.5
2x1100lbs, 370lbs, center hard tank+IBS
ACME 1235 prop
Wakeboard Hyperlite Belmont
Wakeskate Hyperlite Byerly
Wakesurf Hyperlite Broadcast 5.4
-
07-12-2013, 09:34 AM #128Hey, Its Moomba time
Its all about the dash - enjoy the dash, as that is your time between the dates
13 Mobius LSV-sold
08 Mobius LSV-sold
03 Mobius LSV-sold
life is about finding the balance between being a responsible adult and staying young at heart
-
07-12-2013, 10:23 AM #129
I think most everyone on here with a Mojo has the 1235 and it does the job without complaint!
2012 Mojo
2009 LS (SOLD!!!)
2010 Tundra 5.7 Crewmax 4X4
-
07-12-2013, 10:28 AM #130