Results 1 to 10 of 20
-
07-20-2014, 11:55 AM #1Senior Member
- Join Date
- Jun 2007
- Posts
- 883
06 LSV bildge not working, not sure how to remove.
Hey everyone. Been a while since i was on the forums.
06 Möbius LSV
Shaft was leaking bad when I came in yesterday and I didn't notice. It started to rain 4 hours later so I went to cover boat. There was about 4-6 inches of water in hull. Hit the bildge switch and nothing. No light. Hit the reset light and light came on but no bildge.
Used the pump for my ballast bags to drain and tightened the shaft. Stopped the water for now.
But the bildge won't come on.
Is there another fuse beside the resetable one at switch?
If I need to replace the bildge, how do I remove it? How do I disconnect it from the hull?2006 Moomba Mobius LSV
Stereo: Kenwood KMR-D562BT
Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"[/SIZE]
-
07-20-2014, 12:12 PM #2Senior Member
- Join Date
- Jun 2007
- Posts
- 883
This appears direct replacement. Do I need to cut wires or will it just be plug and play? Can't see if there is a harness included.
http://www.skidim.com/prodinfo.asp?number=6031726
Any discounts available at skidim?Last edited by spyder; 07-20-2014 at 12:15 PM.
2006 Moomba Mobius LSV
Stereo: Kenwood KMR-D562BT
Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"[/SIZE]
-
07-20-2014, 09:25 PM #3Senior Member
- Join Date
- Aug 2011
- Posts
- 2,522
Re: 06 LSV bildge not working, not sure how to remove.
Does it turn on when you twist the knob on the side? Usually it gets stuck and doesn't turn on automatically. Open it and clean it, but it happens a lot with that pump style. I add a second pump to solve that..
http://www.instgram.com/jlyons30
2002 Moomba Mobius LSV - Sold
2006 Moomba Mobius LSV - Sold
2017 Moomba Craz - Enzos, Lead
-
07-20-2014, 09:38 PM #4Senior Member
- Join Date
- Jun 2007
- Posts
- 883
-
07-20-2014, 10:00 PM #5
Pop it out of its mount base using a flat head screw driver or strong fingers and see if impeller is jammed, carpet fibers sometimes get in there. Mine broke and I got it at Wally World, and swapped the pumps into the mounts and spliced the power cords.
http://www.walmart.com/ip/Sahara-500...2-VDC/11071160A Day at the Lake...Priceless
A Day in Powder...Endless
Joe V
2012 Möbius XLV~ Loaded & Exiled
2007 Outback V ~ sold
-
07-20-2014, 11:21 PM #6Senior Member
- Join Date
- Jun 2007
- Posts
- 883
-
07-20-2014, 11:30 PM #7Senior Member
- Join Date
- Jun 2007
- Posts
- 883
I *may* have found one locally at Canadian Tire.. I will check to see if they have it in stock tomorrow.
http://www.canadiantire.ca/en/pdp/au...-0793514p.html2006 Moomba Mobius LSV
Stereo: Kenwood KMR-D562BT
Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"[/SIZE]
-
07-21-2014, 09:30 AM #8Senior Member
- Join Date
- Jun 2007
- Posts
- 883
2006 Moomba Mobius LSV
Stereo: Kenwood KMR-D562BT
Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"[/SIZE]
-
07-21-2014, 09:51 AM #9Senior Member
- Join Date
- May 2013
- Posts
- 253
Make sure the circuit board is plugged into the back of the switch. Mine comes undone when tubing really hard. I have to reach from the back along the gunnel to push it back on. The auto switch works but not manual when this happens
-
07-21-2014, 10:03 AM #10Senior Member
- Join Date
- Jun 2007
- Posts
- 883
2006 Moomba Mobius LSV
Stereo: Kenwood KMR-D562BT
Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"[/SIZE]