Results 91 to 100 of 268
Thread: Murder Max Mods
-
01-19-2019, 05:11 PM #91
[QUOTE=z28ke;336084]My wife got me this rgb underwater led for Christmas and I got around to installing it today. Had to take the grinder to it as others on this forum have done to clear the wakeplate.
/QUOTE]
What lights are those?
Sent from my P00I using Tapatalk2018 Supra SL400
-
01-19-2019, 09:35 PM #92
It’s the Titan-2 (in rgb) from boatpluglight.com
https://boatpluglight.myshopify.com/...nt=413500536352018 Murder Max
2008 Outback V-Bought new; sold in 2018
-
01-19-2019, 09:44 PM #93
2018 Moomba Craz
6.2L Raptor 400
6 Pump Ballast, Autowake 2.0, Flow 2.0 Surf System
OJ 15x13 Wake Prop
Digital Cruise Pro 3 (paddle wheel)
Wetsounds Rev 10's
2005 Supra Launch 22SSV - Sold
-
01-19-2019, 11:14 PM #94
I doubt it’ll go through since the wires come out of the backside of the drain hole. I always change fluids top side with an oil extractor so it’s no worry for me.
You can kinda see what I mean in this pic from the side
2018 Murder Max
2008 Outback V-Bought new; sold in 2018
-
01-20-2019, 11:52 AM #95
That is a cool gadget and smart engineering solution if you didn’t get the factory underwater lighting.
Sent from my iPhone using Tapatalk2021 Supra SA 400
2018 Supra SA 400 (SOLD)
Michigan
-
01-20-2019, 03:45 PM #96
Here’s what a lot of folks have expressed interest in - adding hinges to the bulky side bench seats on the max.
Keep in mind I am adding ballast under these seats so I don’t need access to the bottom of the compartment. If I was using it for storage I would use a different type of hinge so the seat goes up and back instead of forward and down.
Note: This is a temporary test run to see if they will work. I only put 2 screws in the seat bottom and used double sided sticky tape on the seat base. I’ll go back and add more screws to the seat and drill out the base and use machine screws with washers and nylon lock nuts when I have more time.
A link to the hinges:
https://www.greatlakesskipper.com/lu...SABEgIWwPD_BwE2018 Murder Max
2008 Outback V-Bought new; sold in 2018
-
01-20-2019, 07:36 PM #97
-
02-03-2019, 01:35 PM #98
My wife and in-laws got me the wakemakers 720lb bags for my birthday a couple weeks ago and I just finished the install:
Used a 2 1/4” hole saw to drill through the stringers. The ports on the wakemakers bags are a little further apart than the front ports on the stock rear bags so the holes are offset slightly.
I ordered 8 of these to go over the holes:
https://www.ebay.com/itm/Rig-Rite-Ma...pid=1022100282
2018 Murder Max
2008 Outback V-Bought new; sold in 2018
-
02-03-2019, 01:44 PM #99
On to the vent/overflow...
Green: goes to the vent on the top of the 720
Red: attach the stock vent hose here from the rear bag
Blue: attaches to the vent thru Hull barb
I’m considering Ting into the 720 vent and using 2 fittings on top of the bag like the factory does on the rear bags.
Note: This has not been water tested yet but seems like it’ll work fine based on what others have done.2018 Murder Max
2008 Outback V-Bought new; sold in 2018
-
02-03-2019, 01:53 PM #100
Murder Max Mods
Complete parts list from wakemakers to do it this way (including the crimping tool and a couple extra clamp bands, I think 20ft of hose is enough- I used some extra I had from upgrading my old outbackV a few years ago):
With the 10% off moomba discount this comes in at under $600 not including the rig rite grommets which are optional of course.
I can’t wait to try it out, bring on summer!!!Last edited by z28ke; 02-03-2019 at 01:56 PM.
2018 Murder Max
2008 Outback V-Bought new; sold in 2018