- Tab Content
- Holdmybeer's Activity
- About Me
- Tab Content
-
Older Activity
-
Yesterday, 04:17 PMIf the reservoir is still above the hose you are good. It only is an issue if you get air in the system. Just top off the container and you are...13 replies | 587 view(s)
-
07-25-2024, 04:37 PMKinda obvious but it's painted the same color black as the case.4 replies | 171 view(s)
-
07-23-2024, 05:51 PMHoldmybeer replied to a thread Rewiring Heater pump to NOT run all the time? Been Done? in Service & RepairNext time just stack ice on the heater core to cool the aluminum. Wouldn't have been the most efficient but 5 degrees cooler would have felt like...7 replies | 217 view(s)
-
07-23-2024, 05:49 PMHoldmybeer replied to a thread Rewiring Heater pump to NOT run all the time? Been Done? in Service & RepairI would want them on 2 different switches. Like Knox said, leave the fan switch on the dash but add a switch under the seat for just the pump. This...7 replies | 217 view(s)
-
07-23-2024, 07:06 AMHoldmybeer replied to a thread Rewiring Heater pump to NOT run all the time? Been Done? in Service & RepairCheck your heater plumbing circuit. The pump is running to keep hot closed loop coolant circulating. The heater core will not provide any cooling...7 replies | 217 view(s)
-
07-22-2024, 09:21 PMAt 250hrs you either have a failed seal or a clogged vent. There is a vent with a steel cap that allows pressure to escape all the time. The...4 replies | 171 view(s)
-
07-19-2024, 09:58 PMGot it. I thought you double trailered. That is my fault. There is no way my wife would do the bed camper but truthfully we just need a place...14 replies | 1569 view(s)
-
07-19-2024, 10:24 AMFind out the cost of a new unit and then a rebuild kit. Next figure out your time constraint and see if you can take on the task yourself. The...4 replies | 554 view(s)
-
07-19-2024, 10:20 AMTrayson, I know you double trailer pull all the time. How does that go on the mountain passes? My 2500 could pull the weight but I have never...14 replies | 1569 view(s)
-
07-19-2024, 10:18 AMI hate to hear this. As a father I completely understand, and it helped make your decision easier. However, I was hoping to hear of the adventures...20 replies | 4565 view(s)
-
07-18-2024, 06:41 PMDo not beat yourself up too bad....your friends and family will do that enough...hahaha Good you learned some things in the process that is what...13 replies | 587 view(s)
-
07-17-2024, 02:17 PMUnder the engine hatch behind the engine while standing in the boat looking back. Against the hull you will see 3 black flex ducts zip tied. One of...4 replies | 220 view(s)
-
07-15-2024, 03:32 PMVA LSV is correct. Just follow hoses up. Thru hull to v-drive V-drive to Trans Trans under engine to raw water pump. Water pump to coolant...13 replies | 587 view(s)
-
07-15-2024, 12:05 PMThe pump has to draw water through the v-drive first. It takes a minute before coming out of the exhaust. Are youbgetting water in the bilge? ...13 replies | 587 view(s)
-
07-15-2024, 11:02 AMCheck the ball valve on the thru-hull where the water is sucked in. If some how it got closed you will overheat quickly. The water inlet is the...13 replies | 587 view(s)
-
07-15-2024, 09:10 AMGood to hear it was a simple fix.4 replies | 873 view(s)
-
07-10-2024, 09:10 AMMost boats I have worked on the Filter is the canister style close to the engine. If there is a strainer on the fuel pump assembly, it only gets...21 replies | 1617 view(s)
-
07-09-2024, 08:43 PMTry AC delco 213-895 You should be able to go to a local auto parts and pick one up. The TPS isn't maritime changed but not sure if it is the...21 replies | 1617 view(s)
-
07-09-2024, 11:38 AMNevermind the PCM comment...you probably have the indmar assault.21 replies | 1617 view(s)
-
07-09-2024, 11:15 AMSure does! The 2003 is PCM engine and is GM based. The TPS should be an easy part to source.21 replies | 1617 view(s)
-
07-09-2024, 11:13 AMIf you go into system settings you should be able to reset ballast level to empty or full.4 replies | 873 view(s)
-
07-08-2024, 09:46 AMYour pump definitely got hot and bubbled the paint. The hoses loosened up from being heated and the pressure will slide them off. Your oil...10 replies | 529 view(s)
-
07-07-2024, 10:00 PMI am not sure if it is NMEA 0183. CAN is typically devicenet but the speed is analog if it is the paddle wheel. If your zero off is gps then...3 replies | 237 view(s)
-
07-07-2024, 10:23 AMThe problem you have is our older boats use CAN for temp and depth and then analog (paddle wheel) for speed. The newer boats use NEMA2000 and gps...3 replies | 237 view(s)
-
07-04-2024, 09:13 AMWD-40 - with engine running, spray around mounting surfaces and hoses. If the idle increases or smoothes out, that is your leak. The wd-40 acts...21 replies | 1617 view(s)
-
07-03-2024, 11:13 PMCarb engine I would check return springs on carb or vacuum leaks. Intake manifold leak will cause high rev idle and stalling. Fuel injection I...21 replies | 1617 view(s)
-
07-03-2024, 10:32 PMLook under the steering wheel, or by the batteries. Also a bad crank position sensor and/or cam position sensor will cause the injectors to not...1 replies | 130 view(s)
-
07-02-2024, 06:08 PMFor reference my mojo on lake water never goes over 165 even surfing heavy. Fake-a-lake is 160 but no revving. Thermostat opens at 160. 210 is...10 replies | 529 view(s)
-
07-01-2024, 06:17 PMThat hose does not need to be removed but it is a quick way to drain the raw water system for winter. I would check your v-drive fluids and make...10 replies | 529 view(s)
-
07-01-2024, 06:11 PMAny idea what your temp gauge was reading? I used to get a warning of low water flow. My idler pulley seized a few month later. I changed the...9 replies | 496 view(s)
About Holdmybeer
Basic Information
About Holdmybeer
- Location:
- Columbus, Ohio
Signature
2015 Moomba Mojo Surf Edition
4,000lbs
Manual Flow
4,000lbs
Manual Flow
Statistics
Total Posts
- Total Posts
- 1,324
- Posts Per Day
- 1.03
General Information
- Last Activity
- Yesterday 10:21 PM
- Join Date
- 01-18-2021
- Referrals
- 0