![Moomba on Facebook Moomba on Facebook](/assets/images/chicklet_facebook.gif)
![Moomba on Twitter Moomba on Twitter](/assets/images/chicklet_twitters.gif)
![Moomba on Vimeo Moomba on Vimeo](/assets/images/chicklet_vimeo.gif)
![Moomba on Instagram Moomba on Instagram](/assets/images/chicklet_instagram.gif)
![Moomba on Blogger Moomba on Blogger](/assets/images/chicklet_blogger.gif)
'02 Outback LSV
I would like to add a shutoff – valve to my boat. It is more for a safety factor then anything else, plus I think it is required now on new boats.
I have looked at Lowes and Home Depot and found a 1.25 valve (don’t recall if it was full flow) and a PVC nipple, have not located a female elbow. From the looks I am not even sure if I can remove the existing male barb elbow without dropping the inlet strainer down for clearance to remove the elbow.
It seems it could be done 2 ways.
1) Splice the valve in the existing 1.25 hose (2 male barb nipples and ball valve)
2) Remove the current elbow start from there (female elbow, close nipple, ball valve, male barb nipple)
I have located a 1.25 ball-valve, and a barb nipple, but it seems I may have to order the rest from various sites. It would be great to get all the parts from one place and know they will connect. I am ignorant about the thread types and those details.
I am looking for some advice and ideally pictures of an existing setup.
2014 Mojo Surf
2013 Mojo Sold
2010 LSV Sold
2002 OB LSV Sold
Are putting a shut off valve on your water supply to the engine? If so, be sure to add an interlock switch to your engine.
1998 Mobius
310 HP PCM
SOLD
Yes, the inlet water. I plan to tie wrap it open or maybe remove the handle to prevent a dumbbutt move on someones part.
Can anyone speak if a valve is factory installed on new boats and how they are setup?
2014 Mojo Surf
2013 Mojo Sold
2010 LSV Sold
2002 OB LSV Sold
Mc, i'll try to remember and hop up in the boat when i get home and see what i have-its a 08 lsv, i'll snap a photo for ya
Hey, Its Moomba time
Its all about the dash - enjoy the dash, as that is your time between the dates
13 Mobius LSV-sold
08 Mobius LSV-sold
03 Mobius LSV-sold
life is about finding the balance between being a responsible adult and staying young at heart
Hey, Its Moomba time
Its all about the dash - enjoy the dash, as that is your time between the dates
13 Mobius LSV-sold
08 Mobius LSV-sold
03 Mobius LSV-sold
life is about finding the balance between being a responsible adult and staying young at heart
What is the reason for the valve? The more connectors and valves connected to your fresh water line the higher probability of a failure. The failure of the water line in a static condition (sitting in the water) is very small and the probability of failure actually increases with the addition of the valve even when it is positioned correctly. Good luck with that one and if you sell the boat let the new owner know.
1998 Mobius
310 HP PCM
SOLD
I dont have 100% comformation, but I have read somewhere on new boats of this nature they are required by some safety standard.
Dpending on your water level if one has a water strainer, you may need to stop the flow if you need to clean while in the water.
There was already a shut-off valve in place on my ballast inlet.
2014 Mojo Surf
2013 Mojo Sold
2010 LSV Sold
2002 OB LSV Sold
That would make sense for a strainer unless the strainer was located above the water level like the raw water pump on my boat where I can change it while on the water. Since that action is a controlled process, I would have a means to make it difficult to close the valve by an inattentive mechanic or someone horseplaying. I would think the strainer would have the valve built in to eliminate the need for another hose connection.
Last edited by zabooda; 04-01-2009 at 05:03 PM.
1998 Mobius
310 HP PCM
SOLD
2014 Mojo Surf
2013 Mojo Sold
2010 LSV Sold
2002 OB LSV Sold