Results 11 to 20 of 21
Thread: Replacing Shaft Packing?
-
05-13-2008, 11:26 AM #11
These are the instructions that were sent to my by Brian Raymond, they are on the bottom of the instructions for the Shaft Alignment process. I just copy pasted the instructions I received from Skiers Choice. Hopefully someone from the factory will chime in and verify them.
15 Mondo Surf Edition
02 LSV - Traded In
-
05-13-2008, 06:38 PM #12Senior Member
- Join Date
- Jun 2007
- Posts
- 883
well the shop near my place just said they wont be able to get to my boat until next week, so i may just pull it home and attempt this myself.
the instructions look pretty good.2006 Moomba Mobius LSV
Stereo: Kenwood KMR-D562BT
Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"[/SIZE]
-
05-13-2008, 09:41 PM #13Senior Member
- Join Date
- Jun 2007
- Posts
- 883
just so I know, for when I attempt this on the weekend... you just get it pretty close, then adjust it out on the water to the perfect spec?
2006 Moomba Mobius LSV
Stereo: Kenwood KMR-D562BT
Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"[/SIZE]
-
05-14-2008, 10:36 AM #14Senior Member
- Join Date
- Jun 2007
- Posts
- 883
Well the stuff from skidim won't be here for the weekend, but the local store had some other stuff, I was wondering does this look like the right product?
Appears to be from "Western Pacific Trading, Inc." "Flax Shaft Packing 1/4""
high quality rovings2006 Moomba Mobius LSV
Stereo: Kenwood KMR-D562BT
Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"[/SIZE]
-
05-14-2008, 10:58 AM #15
Spyder,
Looks correct, now the question goes back to JesseC's post quoting Brian Raymond.. Is it 1/4 or is it 3/16"? I too have 06LSV and attempted replacing last weekend with 1/4" GoreTex packing... way tight and nowhere near like when I did my Outback last year.. I have 3/16 on the way, but it will be Fri/Sat before I can get to it. I know what I pulled out of mine seemed smaller than new gore tex, but I assumed it was worn. You may want to see if that local store has some 3/16" too just in case..
You'll need something like an awl or short ice pic to pick out the old packing.. I had a PigTail barbecue turner that I used but it was not best option..Brad
2011 Launch 21V Sold... boatless replaced with a Jeep JKUR
2006 Moomba Mobius LSV sold
2004 Outback sold
-
05-14-2008, 03:52 PM #16
-
05-14-2008, 04:00 PM #17Senior Member
- Join Date
- Jun 2007
- Posts
- 883
Yep, I got the same response from Anthony Cooper.
Hi Derek.
All Moomba D-Drive boats have 1/4" packing. But all of our V-Drives
boats use 3/16" packing.
Also, I just called and left a voice mail for Anthony to drop me that document in a e-mail, if I get it i'll make sure to post it here.Last edited by spyder; 05-14-2008 at 04:10 PM.
2006 Moomba Mobius LSV
Stereo: Kenwood KMR-D562BT
Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"[/SIZE]
-
05-15-2008, 10:24 PM #18Senior Member
- Join Date
- Jun 2007
- Posts
- 883
On a V-Drive, can anyone tell me the size of the lock nut and packing nut so I can be sure to have all the tools with me?
also, what would be the best tool to cut the packing to ensure a straight edge?Last edited by spyder; 05-15-2008 at 11:30 PM.
2006 Moomba Mobius LSV
Stereo: Kenwood KMR-D562BT
Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"[/SIZE]
-
05-16-2008, 08:41 AM #19
Spyder,
I just use channel locks. you should only have to use it on the locking nut. You should be able to move the packing log nut by hand.
Did mine yesterday aft. not too bad. Have fun.
The 3/16 did seem more correct than the 1/4 by the way.Brad
2011 Launch 21V Sold... boatless replaced with a Jeep JKUR
2006 Moomba Mobius LSV sold
2004 Outback sold
-
05-18-2008, 08:51 PM #20Senior Member
- Join Date
- Jun 2007
- Posts
- 883
I replaced the packing with some new packing rope following all instructions. I put it in the water and it was dripping about a drop every 5 seconds out the front where the shaft hole is, and I brought it for a spin and a bunch of wax melted out the front, I drove it for about 10 minutes, brought it back in to take a look and it's still dripping about 1 drop every 5 seconds. I loosened off the lock nut, and tightened it down a fair bit more and it's still dripping about 1 drop every 5 seconds even when the boat is turned off..
Is this normal? I am just gonna leave this wax stuff in, until I get the gore-tex stuff delivered, or if it's decent enough, until the end of the season.
as for the replacement, i pulled all 4 pieces of the old shit out and I put 4 new pieces in (with only 3 I could hand tighten the packing nut all the way down to the bottom of the threads.
any ideas or suggestions?2006 Moomba Mobius LSV
Stereo: Kenwood KMR-D562BT
Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"[/SIZE]