![Moomba on Facebook Moomba on Facebook](/assets/images/chicklet_facebook.gif)
![Moomba on Twitter Moomba on Twitter](/assets/images/chicklet_twitters.gif)
![Moomba on Vimeo Moomba on Vimeo](/assets/images/chicklet_vimeo.gif)
![Moomba on Instagram Moomba on Instagram](/assets/images/chicklet_instagram.gif)
![Moomba on Blogger Moomba on Blogger](/assets/images/chicklet_blogger.gif)
Ran over a mostly submerged branch/log of some sort. Heard it and felt it go under the boat. Immediately put in neutral. After it passed started to throttle up, once hitting about 10mph started to vibrate pretty good so thought for sure prop was damaged. Putted back to pull boat out of water to inspect. Under 10mph no vibration and made it in. Upon putting boat on trailer so could visually inspect, no nicks, bends etc to prop or shaft. Thinking maybe some weeds or something maybe got wrapped around shaft and came off while putting through no wake zone and loading on trailer. It was end of day and last night so never put boat back in to go test to see if vibration was gone now that I knew I had no obvious damage to prop or shaft. When getting home spent more time inspecting again and noticed back side of prop appears to have wear spots on 3 of the 4 blades. Curious if this is normal from use? Prop is about 3 years old or so. Is this wear enough to cause very noticeable vibration? Tried to get pictures, bottom blade has no wear but left and right do in the picture. Top blade also has wear, just didn’t capture in picture. Planning on taking it back out this upcoming weekend to test. Probably more detail than need for my question but wanted to give the whole story of what led me to my question.
2018 Moomba Mondo
My sister in law hit something with our boat. There was no apparent damage but it vibrated at 8 mph. Changed the prop and the vibration went away. Took it to the prop repair shop and there was a slight bend on one of the blades, causing the prop to be out of balance. You have three blades different from the fourth. That could be enough.
2016 Moomba Mojo Surf Edition
2000 Sharpe Houseboat 70x16 (Lives at Lake Powell)
If the log hit hard enough it could have tweaked the brackets holding the prop shaft (going to get roasted for not knowing the term).
Zog is also right. It doesn't take much for vibration. Could also explain the wear. Depending on how long to putt back it could have caused the polishing effect from the fiction of the water over the 3 blades.
2015 Moomba Mojo Surf Edition
4,000lbs
Manual Flow
Thanks to the both of you. Will swap prop out with my spare and see if issues solved. Great way to describe the wear “polishing effect”. See if the prop change solves (hopefully that all it is), if not may have to to move onto the strut (bracket)as well. When turning prop by hand, all seems to be smooth turning so we shall see. Will follow up after I get chance to drop it back into the water.
2018 Moomba Mondo
How fast were you moving when you hit the log? Even going really slow, if the log was big enough in mass, it could have slightly knocked the pitch out of one of the blades. That would be hard to see by just rotating it on the shaft. If you take it off, you might be able to tell measuring it on a flat surface.
Sent from my SM-G781V using Tapatalk
2021 Moomba Makai
Black Cherry Metal Flake & Fire Red
Nibral OJ 15.5x15 Altitude/Wake prop w/1.76 trans v-drive
Wet Sounds bow speakers & 10's on the Tower & ported sub
Was probably moving about 20 or so, storm was rolling in so was heading in to get off lake. Waves were pretty good as well so think that contributed to not seeing the floating debris. Daughter was sitting up front, when running it over she said cant believe you didn't see it, it was HUGE! Changing prop out this evening and will head to lake in the morning to give it a run.
2018 Moomba Mondo
It really is about the balance of the prop overall. Like I said, our damage was almost imperceptible. My brother-in-law hit an underwater shoal at Lake Powell last weekend and trashed his prop, with all 4 blades getting trashed. He was able to drive his boat at 15 mph before vibrating since the damage was more balanced than ours.
2016 Moomba Mojo Surf Edition
2000 Sharpe Houseboat 70x16 (Lives at Lake Powell)
Prop change took care of the vibration. Looks like will be sending out the old to get checked/balanced so I still have a backup. Thanks all.
2018 Moomba Mondo
It is amazing how the slightest imperfection you can't see with the naked eye can throw a prop outta balance. Could be a warped ear or bent at the hub. Put it on a flat surface, if it wobbles, it is the hub and most likely shot. Hopefully not though and just needs repitched.
2018 Supra SA400 aka The Ron Burgandy
2011 Sea-Doo Wake 155
2015 Mojo Surf, sold...2013 Axis A22 Recon Edition, sold...2010 Axis A22, sold...2007 Maxum 1800sr3, sold
I think what you see on the back of your blades is not wear. I am pretty sure its just where material was removed as part of the balancing when the prop was made.
David
2017 Moomba Mojo Max Surf Edition, 2 Pair Wetsounds Rev10s powered by an SD2, 6 pair Wetsounds XS650M and Wetsounds XS12 powered by SD6 all controlled by a WS420. 2 Lumitec SeaBlaze X2 Spectrum underwater lights
SOLD***2008 Mobius LSV, Gravity III , Wake Plate, Z5, Exile SX65c's, Exile XM9s, Exile XI12D, Exile Javelin, Exile 30.2***SOLD