Results 41 to 50 of 90
Thread: August 2022 pics and vids
-
08-23-2022, 10:06 AM #41Member
- Join Date
- Aug 2020
- Location
- Charlotte, NC
- Posts
- 74
-
08-23-2022, 11:10 AM #42
Im the worlds worst at taking pictures but there were probably 20 boats there for the meetup plus a ton of others just hanging out. It really was a great time. If Skiers Choice was smart they would get behind this and make it a big deal like Malibu does their meetup. Will see if my wife has some more pics of the event. My phone stayed in the boat most of the weekend.
2019 Craz
OJ 950
Wakemakers bags
Heatercraft triple heater
-
08-23-2022, 11:56 AM #432018 Supra SA400 aka The Ron Burgandy
2011 Sea-Doo Wake 155
2015 Mojo Surf, sold...2013 Axis A22 Recon Edition, sold...2010 Axis A22, sold...2007 Maxum 1800sr3, sold
-
08-24-2022, 12:29 PM #44
Such a nice looking boat! I can not believe how tall these new boats are on the trailer. I always put my drain plug in a cup holder and can easily reach over and grab it before launching.
2006 Supra Launch 21V
-
08-24-2022, 12:39 PM #45Senior Member
- Join Date
- Apr 2012
- Location
- Lexington, SC
- Posts
- 542
The SL is really deep, but it's great for the kiddo and storage. We just spent a week at the lake and it is a great boat. Lots of compliments on the colors. I have to get the interior and a few more pictures added.
-
08-24-2022, 12:42 PM #46
That's funny you say that becasue i used to be able to do the same thing and reach over the side of our 07 LSV and get the plug out of the cup holder. Now with our new Craz..... not a chance.
Last edited by 996scott; 08-24-2022 at 12:56 PM.
Scott
2021 Craz
2007 Mobius LSV
1997 Sea Ray 190
-
08-24-2022, 01:42 PM #47
Prepping for new WM bags, and since my stock bags would pop out the engine dividers…
2A096819-9ED7-4B76-B53A-C0919F7861E7.jpg
1x1 1/8 angle iron, cut to about 28” pretty close to the bottom channel and to not interfere with the upper locking nut and not scrape on the gel coat
53B614D5-FFBD-4754-B989-090753FB39DE.jpg
Using the existing hardware
FCD5B3B1-37D8-4919-B2C2-36948E455A43.jpg
Cleaned up and drilled, stock hardware is exactly 10” apart
AD9A1297-A8F3-4FB0-971E-51A8FBB73C5E.jpg
Filed down any sharp edges and painted
032ADA4B-76E2-4641-B174-E7F9330EF4DB.jpg
Installed just one per side to test…..2022 Makai
Fire Red - Pecan ChillTech - Woodgrain Gatorstep
400 - 1.76 - 15.5x15 prop (16x13 Acme 3409 installed for testing)
Ballast Mods: 1000lb of lead and WM Bags
-
08-24-2022, 01:46 PM #48
Continued due to 5 pictures per post
BA7581A4-1E8F-48B5-A198-15AF2CE3EC76.jpg
D61D9DBA-7A36-43F5-983B-36E6F5B6FAA9.jpg
Have enough material to add a second per panel, plus some 1” 1/8 flat stock to utilize if required as well….
Was $24 bucks for enough material to make 6 angle iron brackets and 6 flat stock braces…. Surprised metal was still that cheap
I know everyone has done this a few times, and knows the issues…. I did notice on the front and back panels they had a small screw in the lower c channel holding them in place, but did not stop the front from popping out at the top after the middle had already pushed into the engine….2022 Makai
Fire Red - Pecan ChillTech - Woodgrain Gatorstep
400 - 1.76 - 15.5x15 prop (16x13 Acme 3409 installed for testing)
Ballast Mods: 1000lb of lead and WM Bags
-
08-24-2022, 06:27 PM #49Senior Member
- Join Date
- Jun 2010
- Location
- Colorado Springs
- Posts
- 114
-
08-24-2022, 08:45 PM #502021 Moomba Makai
Black Cherry Metal Flake & Fire Red
Nibral OJ 15.5x15 Altitude/Wake prop w/1.76 trans v-drive
Wet Sounds bow speakers & 10's on the Tower & ported sub