Page 9 of 9 FirstFirst ... 789
Results 81 to 90 of 90
  1. #81
    Join Date
    Jun 2008
    Location
    Henderson, NV
    Posts
    6,849

    Default

    Quote Originally Posted by HFarr View Post
    Yes I remember that. The 4 Runner that Marty McFly had was Sweet too!

    Sent from my SM-G781V using Tapatalk
    not quite a 4runner but close...
    '06 Supra Launch 20SSV-gone but never forgotten

  2. #82
    Join Date
    Mar 2021
    Location
    South Georgia
    Posts
    1,463

    Default

    You did put 2 coats of wax on that....right?

    Sent from my SM-G781V using Tapatalk
    2021 Moomba Makai
    Black Cherry Metal Flake & Fire Red
    Nibral OJ 15.5x15 Altitude/Wake prop w/1.76 trans v-drive
    Wet Sounds bow speakers & 10's on the Tower & ported sub

  3. #83
    Join Date
    Mar 2021
    Location
    South Georgia
    Posts
    1,463

    Default

    Quote Originally Posted by HFarr View Post
    I posted these before, but this is how I reinforced my panels. I took the steel channel back off and painted them with high heat black paint too. Shown here unpainted. Burped and adjusted my WM bag and it gets really full now too.

    Sent from my SM-G781V using Tapatalk
    This is the metal I used to make my panel stiffeners out of. Picked them up at Home Depot and painted them with some high temp engine enamel after I cut and drilled them. I believe I cut them off at about 28" each. And I did not pay $19 each for them. I think they were 10 each.

    Sent from my SM-G781V using Tapatalk
    2021 Moomba Makai
    Black Cherry Metal Flake & Fire Red
    Nibral OJ 15.5x15 Altitude/Wake prop w/1.76 trans v-drive
    Wet Sounds bow speakers & 10's on the Tower & ported sub

  4. #84
    Join Date
    May 2010
    Location
    Salt Lake City, Utah
    Posts
    1,599

    Default

    Quote Originally Posted by sandm View Post
    not quite a 4runner but close...
    oh man that was quite the ride back in the day! LOL
    Scott
    2021 Craz
    2007 Mobius LSV
    1997 Sea Ray 190

  5. #85
    Join Date
    Mar 2021
    Location
    South Georgia
    Posts
    1,463

    Default

    I just found out one of my friends still has his that he bought new in 1986 under a tarp at the lake! A white one though.

    Sent from my SM-G781V using Tapatalk
    2021 Moomba Makai
    Black Cherry Metal Flake & Fire Red
    Nibral OJ 15.5x15 Altitude/Wake prop w/1.76 trans v-drive
    Wet Sounds bow speakers & 10's on the Tower & ported sub

  6. #86
    Join Date
    Feb 2018
    Location
    Boating on Lake Martin, AL
    Posts
    1,382

    Default

    Buddy of mine has one as well. She ain’t showroom new looking but still runs like a champ. I believe it’s in the stock motor as well. It gets used as it should and Marty McFly would approve I think





    2019 Moomba Max "MOOMBAE"
    Mods: Wakemakers upgrade + 500 lbs of lead
    2016 Yamaha AR192 - sold

  7. #87
    Join Date
    Mar 2022
    Location
    Winston Salem NC
    Posts
    116

    Default


    Finished my project. Like HFARR, I used 1/8 angle iron on all the panels (+ my wake makers reinforcement kit). Then, I took out the old track and used this on both sides and the back.

    For the back (carpeted panels) I actually used the large angle iron on the back then put the original channel back on top of it. Also put one piece of angle iron in the back of those panels.

    Went out today and no issues ! Not the cleanest upgrade in terms of looks but very effective. Only getting maybe 1/8 of panel movement , if that.


    Sent from my iPhone using Tapatalk
    2022 Makai 400
    15.5x16.5 prop (18 back up)
    Chilltech
    Premium Wetsounds Package
    WakeMakers bag upgrade

  8. #88
    Join Date
    Mar 2021
    Location
    South Georgia
    Posts
    1,463

    Default

    So you have a continuous piece of angle all the way along the length of the panels for the engine side at the bottom with some shorter pieces along the bag sides of the panels? That creates the slot to hold the panels at the bottom. Do you have an overall photo of it?

    Sent from my SM-G781V using Tapatalk
    2021 Moomba Makai
    Black Cherry Metal Flake & Fire Red
    Nibral OJ 15.5x15 Altitude/Wake prop w/1.76 trans v-drive
    Wet Sounds bow speakers & 10's on the Tower & ported sub

  9. #89
    Join Date
    Mar 2022
    Location
    Winston Salem NC
    Posts
    116

    Default

    Quote Originally Posted by HFarr View Post
    So you have a continuous piece of angle all the way along the length of the panels for the engine side at the bottom with some shorter pieces along the bag sides of the panels? That creates the slot to hold the panels at the bottom. Do you have an overall photo of it?

    Sent from my SM-G781V using Tapatalk
    Correct. I took photos while I was doing it but Ill get a better one and upload.


    Sent from my iPhone using Tapatalk
    2022 Makai 400
    15.5x16.5 prop (18 back up)
    Chilltech
    Premium Wetsounds Package
    WakeMakers bag upgrade

  10. #90
    Join Date
    Mar 2022
    Location
    Winston Salem NC
    Posts
    116

    Default


    This was mid project , but nothing much changed.


    Sent from my iPhone using Tapatalk
    2022 Makai 400
    15.5x16.5 prop (18 back up)
    Chilltech
    Premium Wetsounds Package
    WakeMakers bag upgrade

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •