Results 41 to 50 of 72
Thread: Air in Ballast Bags - 22 Mojo
-
07-16-2022, 08:50 AM #41
See around the 1:00 mark on my video and you’ll see it while I talk about it. Note I think the sensor style and position has changed over the years as I’ve seen different setups on some of the newer boats. The reason why it does it more on the WM bag is the bag is taller and unless the sensor location changes (moves higher) water will get to it before the bag is full.
2019 Moomba Max "MOOMBAE"
Mods: Wakemakers upgrade + 500 lbs of lead
2016 Yamaha AR192 - sold
-
07-16-2022, 09:18 AM #42
This is the rear port flow sensor on my 2021 Makai. It is at the top of the hard tube, but I probably need to move it o up or over to the flex tube. Mine shuts off before completely filling the bag too.
Sent from my SM-G781V using Tapatalk2021 Moomba Makai
Black Cherry Metal Flake & Fire Red
Nibral OJ 15.5x15 Altitude/Wake prop w/1.76 trans v-drive
Wet Sounds bow speakers & 10's on the Tower & ported sub
-
07-16-2022, 11:41 AM #43Senior Member
- Join Date
- Jul 2021
- Posts
- 100
Very helpful! Thanks.
-
07-16-2022, 12:00 PM #44Senior Member
- Join Date
- Jul 2021
- Posts
- 100
-
07-16-2022, 06:18 PM #45
Not sure honestly. I heard some others talking about getting error messages if you disconnect them though.
Sent from my SM-G781V using Tapatalk2021 Moomba Makai
Black Cherry Metal Flake & Fire Red
Nibral OJ 15.5x15 Altitude/Wake prop w/1.76 trans v-drive
Wet Sounds bow speakers & 10's on the Tower & ported sub
-
07-18-2022, 12:30 PM #46
How are people moving that when it's that full tube setup on the bag sensor? I have the same in my 21 Makai and was trying to figure out how to movie it.
2021 Moomba Makai
Minnesota
-
07-18-2022, 01:21 PM #47
Looks to me the tube is just a “cover” over existing ballast tubing to keep it vertical. The top of the tube looks like a separate piece than and the sensor is slide in between it all. My guess is the top piece can be removed and sensor replaced or moved but hard to tell without being in front of my. Thankfully the only tube I have like that is the draft sensor used for amplitude readings.
2019 Moomba Max "MOOMBAE"
Mods: Wakemakers upgrade + 500 lbs of lead
2016 Yamaha AR192 - sold
-
07-18-2022, 05:23 PM #48
That longer hard plastic tube has a clamp going to the flex tube at both ends. I had someone tell me to raise their sensor, they replaced the short piece with a longer piece of flex tube at the bottom. Then just remounted the whole assembly up higher.
Sent from my SM-G781V using Tapatalk2021 Moomba Makai
Black Cherry Metal Flake & Fire Red
Nibral OJ 15.5x15 Altitude/Wake prop w/1.76 trans v-drive
Wet Sounds bow speakers & 10's on the Tower & ported sub
-
07-18-2022, 06:58 PM #49Senior Member
- Join Date
- Jul 2021
- Posts
- 100
-
07-19-2022, 07:54 AM #50
This is how I did mine…….
Took a 90 deg fitting, some tubing and a few clamps
Sent from my iPhone using Tapatalk2019 Makai
Raptor 450 w/ 1.76 Trans
WakeMakers 1350s in the rear & 1K in Lead