Results 91 to 100 of 127
-
07-13-2022, 01:17 AM #91Senior Member
- Join Date
- Mar 2020
- Posts
- 127
Wow - I just installed the same kit but no where near that full. Leaves me wondering how much weight I’m leaving on the table…lol.
I don’t have the vent setup like you do, I was unscrewing one of the caps to get the air out but when they were flowing water out the top and no air any longer I just let the pump run until I thought they were tight. No idea they could swell that big!2019 Moomba Makai
400 Raptor
650 lbs lead
Wakemakers rear upgrade
-
07-22-2022, 06:01 PM #92Member
- Join Date
- Aug 2018
- Posts
- 88
Adjusted my timers and took a pick of my bags for reference.
Sent from my iPhone using Tapatalk
-
07-22-2022, 07:03 PM #93
-
07-22-2022, 11:26 PM #94Member
- Join Date
- Aug 2018
- Posts
- 88
-
07-23-2022, 07:52 PM #95
My WM bags don't get that high when I fill them. I gotta figure out what's up!
Sent from my SM-G781V using Tapatalk2021 Moomba Makai
Black Cherry Metal Flake & Fire Red
Nibral OJ 15.5x15 Altitude/Wake prop w/1.76 trans v-drive
Wet Sounds bow speakers & 10's on the Tower & ported sub
-
07-23-2022, 10:03 PM #96Member
- Join Date
- Aug 2018
- Posts
- 88
-
07-24-2022, 12:44 PM #97
Good lord I can't tell you how disappointed I am with these cheap panels that Skiers is using. Reinforced my side panels, and now my rear locker panel is popping out on the port side! I even put two screws in the bottom of it as a precaution when I installed the WM bags. Last time out it bowed and popped out of the track! I guess I will have to figure out how to stiffen it too!
Sent from my SM-G781V using Tapatalk2021 Moomba Makai
Black Cherry Metal Flake & Fire Red
Nibral OJ 15.5x15 Altitude/Wake prop w/1.76 trans v-drive
Wet Sounds bow speakers & 10's on the Tower & ported sub
-
07-24-2022, 03:11 PM #98
Mine pop out of the track every time. Kinda worried about the exhaust manifold heat against them.
Sent from my iPhone using Tapatalk
-
07-25-2022, 07:47 AM #99
Man that is a bummer to hear. I will have to keep an eye on my rears panels. I used WakeMakers Kit to reinforce mine engine dividers and actually bought 2 kits as I wanted to add some rigidity to more than just the main panels. I still have 2 pieces of channel that I didn't use and the hardware to go with it so I might just add it there.
2019 Makai
Raptor 450 w/ 1.76 Trans
WakeMakers 1350s in the rear & 1K in Lead
-
07-29-2022, 03:05 PM #100Senior Member
- Join Date
- Mar 2022
- Location
- Winston Salem NC
- Posts
- 155
[QUOTE=TXSurf4;380319]No the vent wasn't kinked at all as it was spewing out. It definitely filled the entire locker which is what you would expect it to do. I am going to work on figuring out how to get them to fill like this every time though.
Any luck on this?? I need to know2022 Makai 400
15.5x16.5 prop (18 back up)
Chilltech
Premium Wetsounds Package
WakeMakers (custom) bag upgrade