Page 10 of 11 FirstFirst ... 891011 LastLast
Results 91 to 100 of 110
  1. #91
    Join Date
    Mar 2020
    Posts
    110

    Default

    Wow - I just installed the same kit but no where near that full. Leaves me wondering how much weight I’m leaving on the table…lol.

    I don’t have the vent setup like you do, I was unscrewing one of the caps to get the air out but when they were flowing water out the top and no air any longer I just let the pump run until I thought they were tight. No idea they could swell that big!
    2019 Moomba Makai
    400 Raptor
    650 lbs lead
    Wakemakers rear upgrade

  2. #92

    Default

    Adjusted my timers and took a pick of my bags for reference.





    Sent from my iPhone using Tapatalk

  3. #93
    Join Date
    Mar 2021
    Location
    South Georgia
    Posts
    1,369

    Default

    Quote Originally Posted by Schlanseay View Post
    Adjusted my timers and took a pick of my bags for reference.





    Sent from my iPhone using Tapatalk
    Is that on a Makai or Max?

    Sent from my SM-G781V using Tapatalk
    2021 Moomba Makai
    Black Cherry Metal Flake & Fire Red
    Nibral OJ 15.5x15 Altitude/Wake prop w/1.76 trans v-drive
    Wet Sounds bow speakers & 10's on the Tower & ported sub

  4. #94

    Default

    Quote Originally Posted by HFarr View Post
    Is that on a Makai or Max?

    Sent from my SM-G781V using Tapatalk
    Itís on a Kaiyen!


    Sent from my iPhone using Tapatalk

  5. #95
    Join Date
    Mar 2021
    Location
    South Georgia
    Posts
    1,369

    Default

    My WM bags don't get that high when I fill them. I gotta figure out what's up!

    Sent from my SM-G781V using Tapatalk
    2021 Moomba Makai
    Black Cherry Metal Flake & Fire Red
    Nibral OJ 15.5x15 Altitude/Wake prop w/1.76 trans v-drive
    Wet Sounds bow speakers & 10's on the Tower & ported sub

  6. #96

    Default

    Quote Originally Posted by HFarr View Post
    My WM bags don't get that high when I fill them. I gotta figure out what's up!

    Sent from my SM-G781V using Tapatalk
    Try filling them about 20 % and gently pull up on the long sides of the bags on each side. Mine were laying over lapped on the bottom side.


    Sent from my iPhone using Tapatalk

  7. #97
    Join Date
    Mar 2021
    Location
    South Georgia
    Posts
    1,369

    Default

    Good lord I can't tell you how disappointed I am with these cheap panels that Skiers is using. Reinforced my side panels, and now my rear locker panel is popping out on the port side! I even put two screws in the bottom of it as a precaution when I installed the WM bags. Last time out it bowed and popped out of the track! I guess I will have to figure out how to stiffen it too!

    Sent from my SM-G781V using Tapatalk
    2021 Moomba Makai
    Black Cherry Metal Flake & Fire Red
    Nibral OJ 15.5x15 Altitude/Wake prop w/1.76 trans v-drive
    Wet Sounds bow speakers & 10's on the Tower & ported sub

  8. #98
    Join Date
    Feb 2019
    Location
    Tulsa
    Posts
    137

    Default

    Mine pop out of the track every time. Kinda worried about the exhaust manifold heat against them.


    Sent from my iPhone using Tapatalk
    Ď22 Makai
    '06 Gravity XLV -sold
    https://www.youtube.com/GreaseMonkeyTV

  9. #99
    Join Date
    Oct 2018
    Location
    Hockley, Tx
    Posts
    990

    Default

    Quote Originally Posted by HFarr View Post
    Good lord I can't tell you how disappointed I am with these cheap panels that Skiers is using. Reinforced my side panels, and now my rear locker panel is popping out on the port side! I even put two screws in the bottom of it as a precaution when I installed the WM bags. Last time out it bowed and popped out of the track! I guess I will have to figure out how to stiffen it too!

    Sent from my SM-G781V using Tapatalk
    Man that is a bummer to hear. I will have to keep an eye on my rears panels. I used WakeMakers Kit to reinforce mine engine dividers and actually bought 2 kits as I wanted to add some rigidity to more than just the main panels. I still have 2 pieces of channel that I didn't use and the hardware to go with it so I might just add it there.
    2019 Makai
    Raptor 450 w/ 1.76 Trans
    WakeMakers 1350s in the rear & 1K in Lead

  10. #100
    Join Date
    Mar 2022
    Location
    Winston Salem NC
    Posts
    88

    Default

    [QUOTE=TXSurf4;380319]No the vent wasn't kinked at all as it was spewing out. It definitely filled the entire locker which is what you would expect it to do. I am going to work on figuring out how to get them to fill like this every time though.


    Any luck on this?? I need to know
    2022 Makai 400
    15.5x16.5 prop (18 back up)
    Chilltech
    Premium Wetsounds Package
    WakeMakers bag upgrade

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •