Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 27
  1. #11
    Join Date
    Apr 2013
    Location
    Calgary Ab
    Posts
    61

    Default

    Could you not calibrate you boat with weight in you boat as long as it's sitting flat on the water?

    Sent from my SM-G998W using Tapatalk
    2019 Moomba Mojo

  2. #12
    Join Date
    May 2017
    Location
    Alberta, Canada
    Posts
    304

    Default

    Quote Originally Posted by duch17 View Post
    Could you not calibrate you boat with weight in you boat as long as it's sitting flat on the water?
    If you're referring to inclinometer calibration, any ballast weight (water/leadwake) is going to skew the numbers in my opinion. If you're referring to the draft sensor, I don't know and haven't seen Jon/Goose comment on that point.
    2021 Mojo, 6.2L Raptor 400/1.76, Acme 3407 15.5x13, G6, Flow3, +6500 lbs ballast
    2005 Mobius LSV (sold)
    Windermere Lake, B.C., 2800' Elevation
    2021 Mojo Mods

  3. #13
    Join Date
    Jul 2013
    Location
    Cedar Falls, IA
    Posts
    700

    Default

    Instructions for calibration of both sensors is in the display manual. The draft sensor will be very impacted by weight. The inclinometer zero calibration is the reference point for pitch and roll and is intended to be the boat sitting “flat.” I think it would be really hard to know if your boat was flat I’d you had a lot of gear/ballast/lead/people on board.


    Sent from my iPhone using Tapatalk
    2022 Moomba Mojo
    2013 Moomba Mojo 2.5 (sold)

    Tow - 2019 Ford F150 Ecoboost

  4. #14
    Join Date
    Mar 2012
    Location
    Uniontown, oh
    Posts
    263

    Default

    I was not impressed at 1st as well on my 22. There is a post on here that has pitch and roll setting for ext surf side. Great info. I have a small crew. My wife and 3 kids. 10 6 and 3. I run all ballast full and have 300 led in nose. I do not use auto wake. I use switches to fill bags and make sure they are full. Starboard surf inside 13.5 pitch and 7.5 roll and port surf I use 9.5 pitch and -3.5 roll. 11mph. I don’t really touch wake plate much at all. Wave is nice and clean and can surf it close up and far back for days. More people I get the bigger and even better the wave is. I plane to get more led but just haven’t yet but I’m happy now and it’s better than my 12 mojo. In the beginning like you my 12 was better but now the 22 takes it. It just takes time to play around with it.


    Sent from my iPhone using Tapatalk
    Nick

    2012 moomba mojo 2.5
    2005 Moomba outback-sold

  5. #15
    Join Date
    Apr 2013
    Location
    Calgary Ab
    Posts
    61

    Default

    If I want disable autofill what should my trigger and trigger margin be set at

    2019 mojo with new software

    Should trigger be set really high(myguess)?

    Sent from my SM-G998W using Tapatalk
    2019 Moomba Mojo

  6. #16
    Join Date
    May 2017
    Location
    Alberta, Canada
    Posts
    304

    Default

    Quote Originally Posted by duch17 View Post
    If I want disable autofill what should my trigger and trigger margin be set at

    2019 mojo with new software

    Should trigger be set really high(myguess)?

    Sent from my SM-G998W using Tapatalk
    Not sure what you are referring to here....do you mean "disable autowake" or do you mean "reset/customize ballast timers"? Both are done via the display under vessel settings.
    2021 Mojo, 6.2L Raptor 400/1.76, Acme 3407 15.5x13, G6, Flow3, +6500 lbs ballast
    2005 Mobius LSV (sold)
    Windermere Lake, B.C., 2800' Elevation
    2021 Mojo Mods

  7. #17
    Join Date
    Apr 2013
    Location
    Calgary Ab
    Posts
    61

    Default

    Quote Originally Posted by Hayden View Post
    Not sure what you are referring to here....do you mean "disable autowake" or do you mean "reset/customize ballast timers"? Both are done via the display under vessel settings.
    Disable autofill on the development page, basically adjust the trigger point so it doesn't refill my ballasts.
    I will be back in Invermere hopefully Friday and be able to adjust it again and try I out.

    Sent from my SM-G998W using Tapatalk
    2019 Moomba Mojo

  8. #18
    Join Date
    Apr 2013
    Location
    Calgary Ab
    Posts
    61

    Default

    Quote Originally Posted by duch17 View Post
    Disable autofill on the development page, basically adjust the trigger point so it doesn't refill my ballasts.
    I will be back in Invermere hopefully Friday and be able to adjust it again and try I out.

    Sent from my SM-G998W using Tapatalk
    20220705_150424.jpg
    Picture of the setting page

  9. #19
    Join Date
    Jul 2013
    Location
    Cedar Falls, IA
    Posts
    700

    Default New Software Issues and Performance - 2022 Mojo

    Quote Originally Posted by duch17 View Post
    20220705_150424.jpg
    Picture of the setting page
    I don’t think you need to get into the dealer development page and have them tinker with thresholds, the new SW has a smart tech menu that allows you to turn off the ballast auto fill if I recall correctly


    Sent from my iPhone using Tapatalk
    2022 Moomba Mojo
    2013 Moomba Mojo 2.5 (sold)

    Tow - 2019 Ford F150 Ecoboost

  10. #20
    Join Date
    May 2017
    Location
    Alberta, Canada
    Posts
    304

    Default

    What version of the software are you using? Did you need to use the dealer code to get to the development screen? I don't remember that screen being available, (I may have missed it).

    My software version: MoombaBP_MY22_47740_20211206
    2021 Mojo, 6.2L Raptor 400/1.76, Acme 3407 15.5x13, G6, Flow3, +6500 lbs ballast
    2005 Mobius LSV (sold)
    Windermere Lake, B.C., 2800' Elevation
    2021 Mojo Mods

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •