Results 1 to 9 of 9
-
04-05-2022, 03:46 PM #1Junior Member
- Join Date
- Jun 2021
- Location
- Utah
- Posts
- 21
Tower Gasket Replacement 2006 Moomba
Any idea as to what type of gasket to use for the buffer between the tower and the boat? I have tried this from amazon "TORRAMI Neoprene Rubber Sheet Roll 3/16" (.187") Thick x 12" Wide x 12" Long for DIY Gaskets, Pads, Seals, Crafts, Flooring, Cushioning of Anti-Vibration, Anti-Slip". I'm seeing the neoprene cracking and not looking that good and all it's been doing it sitting in my garage installed on the boat. Any help would be greatly appreciated and Thanks in advance. I can add some pictures later on this evening if needed.
https://www.amazon.com/dp/B08LTJGN8V...t_details&th=1.Ryan
.....But I'd rather be boating.....
1989 Spectrum Fish/Ski **Sold**
2006 Moomba Mobius LSV
-
04-05-2022, 04:58 PM #2
Sounds like you just got some really cheap made neoprene if it's already cracking/dry rotting just sitting there. Maybe some old dated stock they sold you.
Sent from my SM-G781V using Tapatalk2021 Moomba Makai
Black Cherry Metal Flake & Fire Red
Nibral OJ 15.5x15 Altitude/Wake prop w/1.76 trans v-drive
Wet Sounds bow speakers & 10's on the Tower & ported sub
-
04-08-2022, 10:44 AM #3Junior Member
- Join Date
- Jun 2021
- Location
- Utah
- Posts
- 21
Ryan
.....But I'd rather be boating.....
1989 Spectrum Fish/Ski **Sold**
2006 Moomba Mobius LSV
-
04-08-2022, 03:10 PM #4
Yeah, that looks like cheap or old stuff. Or both.
Sent from my SM-G781V using Tapatalk2021 Moomba Makai
Black Cherry Metal Flake & Fire Red
Nibral OJ 15.5x15 Altitude/Wake prop w/1.76 trans v-drive
Wet Sounds bow speakers & 10's on the Tower & ported sub
-
04-09-2022, 11:45 AM #5Junior Member
- Join Date
- Jun 2021
- Location
- Utah
- Posts
- 21
Any idea where to get some that will work?
Ryan
.....But I'd rather be boating.....
1989 Spectrum Fish/Ski **Sold**
2006 Moomba Mobius LSV
-
04-09-2022, 07:18 PM #6
I'd avoid neoprene and go to a rubber sheet.
1998 Mobius
310 HP PCM
SOLD
-
04-24-2022, 12:11 PM #7Junior Member
- Join Date
- Jun 2021
- Location
- Utah
- Posts
- 21
-
04-24-2022, 01:18 PM #8
You're right. Everything showed as neoprene. I found a site that explained the different types and I believe butyl rubber like in inner tubes is the winner.
https://www.mcmaster.com/butyl-rubber-sheets/1998 Mobius
310 HP PCM
SOLD
-
04-24-2022, 08:24 PM #9
This was a common problem with Moombas that had that particular tower, Even my 08 I got in 09 required me to replace them in 11. I just got a firm 1/4 rubber and cut them to match. Its not hard to install, remove the tower bolts, on one side, lift it and you can pull the old one out and use it as a template. Unfortunately I think Moomba used to thin a material and this is why they failed so much.
Malo <--- Means--Evil or Mean One. This explains a lot.
2013 Mojo 2.5 Skylon Tower. Bestia < Beast >
[COLOR="#696969"]