Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 24
  1. #11
    Join Date
    Jul 2021
    Posts
    100

    Default

    Quote Originally Posted by HFarr View Post
    You will need to reinforce the divider panels. They will pop out on you at some point. Skiers Choice should be making a retrofit for these panels in my opinion. They are not designed well. Mine would pop out when just maxing out my stock bags. Make sure to screw the bottom of the panels into the aluminum track too.

    Sent from my SM-G781V using Tapatalk
    So additional drill holes through the plastic dividers and aluminum bracket?

  2. #12
    Join Date
    Mar 2021
    Location
    South Georgia
    Posts
    1,953

    Default

    Not all the way through. Just a small hole in one side of the aluminum channel facing the bag. Then get some 1/2" long "8 stainless sharp point screws and they will self tap into the plastic panel. I put 2 per panel. I also had to do the rear panel covered with carpet. It popped out of the bottom on me too when I put in the WM bags. Those panels just bend too easily. The screws keep the bottoms from pulling up out of that short channel. There was already 1 screw in the front and back panel on mine from the factory.

    Sent from my SM-G781V using Tapatalk
    2021 Moomba Makai
    Black Cherry Metal Flake & Fire Red
    Nibral OJ 15.5x15 Altitude/Wake prop w/1.76 trans v-drive
    Wet Sounds bow speakers & 10's on the Tower & ported sub

  3. #13
    Join Date
    Mar 2021
    Location
    South Georgia
    Posts
    1,953

    Default

    I will get some pictures posted

    Sent from my SM-G781V using Tapatalk
    2021 Moomba Makai
    Black Cherry Metal Flake & Fire Red
    Nibral OJ 15.5x15 Altitude/Wake prop w/1.76 trans v-drive
    Wet Sounds bow speakers & 10's on the Tower & ported sub

  4. #14
    Join Date
    Mar 2021
    Location
    South Georgia
    Posts
    1,953

    Default

    These are the screws I was referring too. They don't need to go all the way through both sides of the aluminum channel. If you use 1/2" long the point on the screw will just make contact with the other side and go all the way through the plastic divider panel.

    Sent from my SM-G781V using Tapatalk
    2021 Moomba Makai
    Black Cherry Metal Flake & Fire Red
    Nibral OJ 15.5x15 Altitude/Wake prop w/1.76 trans v-drive
    Wet Sounds bow speakers & 10's on the Tower & ported sub

  5. #15

    Default

    These are the ones I got from wakemakers




    Sent from my iPad using Tapatalk

  6. #16
    Join Date
    Jul 2021
    Posts
    100

    Default

    Quote Originally Posted by Schlanseay View Post
    These are the ones I got from wakemakers




    Sent from my iPad using Tapatalk
    I bought a set of these. Haven't installed them yet. Looks like they should be installed on the engine side for sure. Will take a little cutting for me unfortunately. I installed noise insulation on that side.

    Everyone doing 2 on the middle panel and one on the stern panel?

  7. #17

    Default

    Yes two then one


    Sent from my iPad using Tapatalk

  8. #18
    Join Date
    Mar 2021
    Location
    South Georgia
    Posts
    1,953

    Default

    I essentially did the same thing buying the channel at Home Depot. Yes install on the engine side and make sure your bolt heads are smooth on the bag side so no snags. This is my setup. I did take them back off and paint them black.

    Sent from my SM-G781V using Tapatalk
    2021 Moomba Makai
    Black Cherry Metal Flake & Fire Red
    Nibral OJ 15.5x15 Altitude/Wake prop w/1.76 trans v-drive
    Wet Sounds bow speakers & 10's on the Tower & ported sub

  9. #19

    Default

    Quote Originally Posted by HFarr View Post
    I essentially did the same thing buying the channel at Home Depot. Yes install on the engine side and make sure your bolt heads are smooth on the bag side so no snags. This is my setup. I did take them back off and paint them black.

    Sent from my SM-G781V using Tapatalk
    Those look great!


    Sent from my iPhone using Tapatalk

  10. #20

    Default

    Didn’t get a great photo of the wave since I was driving but here is my daughter and a glimpse of the wave.


    Sent from my iPhone using Tapatalk

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •