Makai Spare Prop

[TXSurf4]

Has anyone purchased a spare or new prop for their Makai? If so what did you buy? I am looking at purchasing a spare but wanted to get a prop with a different pitch to just try something new. I don't have any complaints with my OJ 932 so should I just buy another?

[Holdmybeer]

With the size and weight of the Makai, and your 450 motor and 1.76 drive I would do with the surf prop that comes on the Supra (if you can fit a 16" prop)
Acme 3591 - https://acmemarine.com/products/acme...8496ed2e&_ss=r

[TXSurf4]

With the size and weight of the Makai, and your 450 motor and 1.76 drive I would do with the surf prop that comes on the Supra (if you can fit a 16" prop)
Acme 3591 - https://acmemarine.com/products/acme...8496ed2e&_ss=r

I know a few people have run 16" props on them with a "very little amount of gel burn" but I am not wanting any gel burn lol. Nettles recommended the Acme 2247 which is a 15x14.25 I have never run a different prop so I wont claim to know anything just thought it was interesting the recommended a smaller diameter prop.

[HFarr]

Your 932 is 15.5 X 16.5. Which is what Moomba refers to as a general use prop. My 2021 Makai runs a 15.5 X 15. They consider it a wake / altitude prop for more power/torque. I have the raptor 400 and it pulls very well with it. I bet your 450 would really pull strong with it.

Sent from my moto z4 using Tapatalk

[TXSurf4]

Your 932 is 15.5 X 16.5. Which is what Moomba refers to as a general use prop. My 2021 Makai runs a 15.5 X 15. They consider it a wake / altitude prop for more power/torque. I have the raptor 400 and it pulls very well with it. I bet your 450 would really pull strong with it.

Sent from my moto z4 using Tapatalk

I have considered it but I am just not sure how the boat will perform with it pulling at surf speeds. I have no desire to wakeboard at full ballast with my setup lol.

[Holdmybeer]

OJ 1951 (15x14) which will pull good heavy for surfing - but losing 1/2" of prop
OJ 930 (15.5x15) as HFarr suggested - look to be the Moomba factory option.
ACME 2847 (15.5x15) - virtually no cup so it will pull surf well
ACME 3829 (15.5x14.5)

I can keep going but not sure you want to make that thing a tug boat. These number should get you good pulling power without too much top end loss.

Tug boat = ACME 2921 (15.5x12.5 cup 0.075)

[larry_arizona]

Personally, these are tow boats and anything that gets fully loaded to surf or wake speed is better for me, as long as revs are reasonable.

I love the 16x13.9 prop, I’d there such a thing as a plate to prevent gel burn?

Anything over 25mph on plane unloaded is a waste to me.


Sent from my iPhone using Tapatalk

[Holdmybeer]

[QUOTE=
Anything over 25mph on plane unloaded is a waste to me.
[/QUOTE]

Someone has never had to get the to restroom in a hurry....lol

[TXSurf4]

Personally, these are tow boats and anything that gets fully loaded to surf or wake speed is better for me, as long as revs are reasonable.

I love the 16x13.9 prop, I’d there such a thing as a plate to prevent gel burn?

Anything over 25mph on plane unloaded is a waste to me.


Sent from my iPhone using Tapatalk

Yes there is Dakota4ce put one on his battle ship Max. It is a small piece of gauge material that looks like a data tag and he screwed it into the fiberglass right there to protect it. Not sure I want to screw in the fiber glass where I don’t need to lol


Sent from my iPhone using Tapatalk

[TXSurf4]

OJ 1951 (15x14) which will pull good heavy for surfing - but losing 1/2" of prop
OJ 930 (15.5x15) as HFarr suggested - look to be the Moomba factory option.
ACME 2847 (15.5x15) - virtually no cup so it will pull surf well
ACME 3829 (15.5x14.5)

I can keep going but not sure you want to make that thing a tug boat. These number should get you good pulling power without too much top end loss.

Tug boat = ACME 2921 (15.5x12.5 cup 0.075)

All of these seem like good options!

TBH I have had a crew of 12 adults in the boat, full ballast and my 1k of lead and the 450 didn’t miss a beat it just eats!!

How would losing a 1/2” affect the performance? I don’t really want to go smaller in diameter if I don’t have to or it doesn’t benefit me.

Anyone have thoughts on ACME vs OJ? Is one better than the other? For what reasons?


Sent from my iPhone using Tapatalk