Results 1 to 10 of 11
Thread: Drill Powered Oil Extractor
-
06-03-2020, 02:54 AM #1
Drill Powered Oil Extractor
I have been looking for was to increase speed and decrease the mess when doing oil changes on the boat and I came across this.
https://www.amazon.com/TOOLGUY-REPUB...cm_wl_huc_item
Anyone have one and if so, how do you like it? Looks like it may be perfect for the application in regards to all the fluid changes on the boat.David
2017 Moomba Mojo Max Surf Edition, 2 Pair Wetsounds Rev10s powered by an SD2, 6 pair Wetsounds XS650M and Wetsounds XS12 powered by SD6 all controlled by a WS420. 2 Lumitec SeaBlaze X2 Spectrum underwater lights
SOLD***2008 Mobius LSV, Gravity III , Wake Plate, Z5, Exile SX65c's, Exile XM9s, Exile XI12D, Exile Javelin, Exile 30.2***SOLD
-
06-03-2020, 07:17 AM #2
I had a cheaper drill pump and it didn’t work on oil.
I highly recommend
OEMTOOLS Manual Extractor 24397 9.5 Liter Hand-Pump Evacuator | Extract Oil, Transmission, Coolant, Other Fluids Through Dipstick Tubes | No Need to Get Under Your Vehicle | No Mess, Easy to Use https://www.amazon.com/dp/B01BW393E2..._wA41EbE1M6R55
Mess free as it gets.
Sent from my iPhone using Tapatalk2021 Supra SA 400
2018 Supra SA 400 (SOLD)
Michigan
-
06-03-2020, 01:31 PM #3Senior Member
- Join Date
- Sep 2005
- Location
- Claytor Lake, VA
- Posts
- 598
I have the OEMTOOLS extractor and love it. I tried drill pumps and cheap battery powered pumps and the vacuum extractor is much quicker and easier.
2005 Mobius LSV
325 EFI
-
06-03-2020, 02:20 PM #4
I have this guy and it works great and only takes like 15 pumps. My Craz fills it. I just detach the house and dump the the top half out in a container and then finish it off. Also use this for the tranny fluid and car oil changes now.
https://www.amazon.com/EWK-Pneumatic...%2C1071&sr=8-52018 Craz, 3000lbs stock ballast, ENZOs, 500lb Lead Ballast, Still chasing the best wave!
-
06-03-2020, 02:42 PM #5Senior Member
- Join Date
- Oct 2016
- Location
- Tims Ford Lake TN
- Posts
- 453
RD, I've tried both and like the other replies, go with the vacuum container extractor type. You won't regret it.
2016 Mojo Surf
Raptor 400
1100 rear bags / 500 IBS / 600 LeadWake
Exile amps/tower - Kicker in-boat
FAE
-
06-03-2020, 02:43 PM #6
I have the pela and it works ok but if I was buying again I'd pick up the one posted above.
there have been several posts in the last 15 years on the drill based and almost everyone said back in the day buy the pela. the one above looks to be a nice improvement over that original vacuum pump.'06 Supra Launch 20SSV-gone but never forgotten
-
06-03-2020, 05:08 PM #7
The OEM tools one is perfect for the raptors, it was the only one I could find to hold 8 qts+.
A few pumps, kick back with a cold beer and viola, done.
You will also need this......
Air hose fittings and Air Coupler... https://www.amazon.com/dp/B074SY2L13...p_mob_ap_share
Sent from my iPhone using Tapatalk2021 Supra SA 400
2018 Supra SA 400 (SOLD)
Michigan
-
06-03-2020, 06:11 PM #8
I have a plea vacuum type. Thought that this may be an improvement to it since all the seals and such are shot on my pela. I’ll look at the OEM one
Sent from my iPhone using TapatalkDavid
2017 Moomba Mojo Max Surf Edition, 2 Pair Wetsounds Rev10s powered by an SD2, 6 pair Wetsounds XS650M and Wetsounds XS12 powered by SD6 all controlled by a WS420. 2 Lumitec SeaBlaze X2 Spectrum underwater lights
SOLD***2008 Mobius LSV, Gravity III , Wake Plate, Z5, Exile SX65c's, Exile XM9s, Exile XI12D, Exile Javelin, Exile 30.2***SOLD
-
06-04-2020, 09:40 PM #9
-
06-05-2020, 06:27 AM #10