Page 1 of 2 12 LastLast
Results 1 to 10 of 11
  1. #1
    Join Date
    Nov 2010
    Location
    Katy, TX
    Posts
    6,069

    Default Drill Powered Oil Extractor

    I have been looking for was to increase speed and decrease the mess when doing oil changes on the boat and I came across this.

    https://www.amazon.com/TOOLGUY-REPUB...cm_wl_huc_item

    Anyone have one and if so, how do you like it? Looks like it may be perfect for the application in regards to all the fluid changes on the boat.
    David

    2017 Moomba Mojo Max Surf Edition, 2 Pair Wetsounds Rev10s powered by an SD2, 6 pair Wetsounds XS650M and Wetsounds XS12 powered by SD6 all controlled by a WS420.

    SOLD***2008 Mobius LSV, Gravity III , Wake Plate, Z5, Exile SX65c's, Exile XM9s, Exile XI12D, Exile Javelin, Exile 30.2***SOLD

  2. #2
    Join Date
    May 2018
    Posts
    1,735

    Default

    I had a cheaper drill pump and it didnít work on oil.

    I highly recommend


    OEMTOOLS Manual Extractor 24397 9.5 Liter Hand-Pump Evacuator | Extract Oil, Transmission, Coolant, Other Fluids Through Dipstick Tubes | No Need to Get Under Your Vehicle | No Mess, Easy to Use https://www.amazon.com/dp/B01BW393E2..._wA41EbE1M6R55

    Mess free as it gets.


    Sent from my iPhone using Tapatalk
    2018 Supra SA 400
    Michigan

  3. #3
    Join Date
    Sep 2005
    Location
    Claytor Lake, VA
    Posts
    535

    Default

    I have the OEMTOOLS extractor and love it. I tried drill pumps and cheap battery powered pumps and the vacuum extractor is much quicker and easier.
    2005 Mobius LSV
    325 EFI

  4. #4
    Join Date
    May 2018
    Location
    ANACORTES, WA
    Posts
    81

    Default

    I have this guy and it works great and only takes like 15 pumps. My Craz fills it. I just detach the house and dump the the top half out in a container and then finish it off. Also use this for the tranny fluid and car oil changes now.

    https://www.amazon.com/EWK-Pneumatic...%2C1071&sr=8-5
    2018 Craz, 3000lbs stock ballast, ENZOs, 500lb Lead Ballast, Still chasing the best wave!

  5. #5
    Join Date
    Oct 2016
    Location
    Tims Ford Lake TN
    Posts
    302

    Default

    RD, I've tried both and like the other replies, go with the vacuum container extractor type. You won't regret it.
    2016 Mojo Surf
    Raptor 400
    1100 rear bags
    Exile amps/tower - Kicker in-boat
    FAE

  6. #6
    Join Date
    Jun 2008
    Location
    Henderson, NV
    Posts
    5,633

    Default

    I have the pela and it works ok but if I was buying again I'd pick up the one posted above.
    there have been several posts in the last 15 years on the drill based and almost everyone said back in the day buy the pela. the one above looks to be a nice improvement over that original vacuum pump.
    '06 Supra Launch 20SSV-gone but never forgotten

  7. #7
    Join Date
    May 2018
    Posts
    1,735

    Default

    The OEM tools one is perfect for the raptors, it was the only one I could find to hold 8 qts+.

    A few pumps, kick back with a cold beer and viola, done.

    You will also need this......


    Air hose fittings and Air Coupler... https://www.amazon.com/dp/B074SY2L13...p_mob_ap_share


    Sent from my iPhone using Tapatalk
    2018 Supra SA 400
    Michigan

  8. #8
    Join Date
    Nov 2010
    Location
    Katy, TX
    Posts
    6,069

    Default

    I have a plea vacuum type. Thought that this may be an improvement to it since all the seals and such are shot on my pela. Iíll look at the OEM one


    Sent from my iPhone using Tapatalk
    David

    2017 Moomba Mojo Max Surf Edition, 2 Pair Wetsounds Rev10s powered by an SD2, 6 pair Wetsounds XS650M and Wetsounds XS12 powered by SD6 all controlled by a WS420.

    SOLD***2008 Mobius LSV, Gravity III , Wake Plate, Z5, Exile SX65c's, Exile XM9s, Exile XI12D, Exile Javelin, Exile 30.2***SOLD

  9. #9
    Join Date
    Sep 2018
    Location
    Eastern Long Island
    Posts
    150

    Default

    Quote Originally Posted by larry_arizona View Post
    I had a cheaper drill pump and it didn’t work on oil.

    I highly recommend


    OEMTOOLS Manual Extractor 24397 9.5 Liter Hand-Pump Evacuator | Extract Oil, Transmission, Coolant, Other Fluids Through Dipstick Tubes | No Need to Get Under Your Vehicle | No Mess, Easy to Use https://www.amazon.com/dp/B01BW393E2..._wA41EbE1M6R55

    Mess free as it gets.


    Sent from my iPhone using Tapatalk
    Do you think it would be OK to use this while at the dock?
    2018 Moomba Max - 400 Raptor - 6 pump ballast - auto wake 2 - flow 2 - gps zero off

  10. #10
    Join Date
    May 2018
    Posts
    1,735

    Default

    Quote Originally Posted by jimmsch View Post
    Do you think it would be OK to use this while at the dock?
    Absolutely


    Sent from my iPhone using Tapatalk
    2018 Supra SA 400
    Michigan

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •