Results 11 to 20 of 55
Thread: Under water lights
-
06-12-2020, 11:30 PM #11
2018 Moomba Craz
6.2L Raptor 400
6 Pump Ballast, Autowake 2.0, Flow 2.0 Surf System
OJ 15x13 Wake Prop
Digital Cruise Pro 3 (paddle wheel)
Wetsounds Rev 10's
2005 Supra Launch 22SSV - Sold
-
06-13-2020, 09:43 AM #12
I believe my 10 watt does have 9 chips too maybe they are smaller?? From the website it looks like the 20W also has 9 chips...
Mike
2013 Outback V
- ballast: 900# rears / 400# center / 650# IBS
- audio: Exile SXT9Q x 2 towers / Kicker KM65 x 6 cabins / Xi 12 sub / Javelin & XM15.4 amps / ZLD
- FAE
- DIY suckgate
2003 SeaRay 182 -- gone but not forgotten...
-
06-13-2020, 11:17 AM #13
Hmmm.... interesting. I didn’t see that. I was going by this statement in their buyers guide. Hopefully I didn’t just get screwed.
Sent from my iPhone using Tapatalk
2018 Moomba Craz
6.2L Raptor 400
6 Pump Ballast, Autowake 2.0, Flow 2.0 Surf System
OJ 15x13 Wake Prop
Digital Cruise Pro 3 (paddle wheel)
Wetsounds Rev 10's
2005 Supra Launch 22SSV - Sold
-
06-13-2020, 12:10 PM #14Senior Member
- Join Date
- Nov 2019
- Posts
- 165
Forgive my ignorance, how are these lights powered? I have a 2019 Helix the drain plug is in the center, is there another plug near my swim platform?
-
06-13-2020, 08:48 PM #15
Yes, there should be another drain plug in the rear just above the wakeplate. My boat was pre-wired for underwater lights in the back. I used one set of leads to light up the Moomba on the back and now will use the other set for the plug light.
Sent from my iPhone using Tapatalk
2018 Moomba Craz
6.2L Raptor 400
6 Pump Ballast, Autowake 2.0, Flow 2.0 Surf System
OJ 15x13 Wake Prop
Digital Cruise Pro 3 (paddle wheel)
Wetsounds Rev 10's
2005 Supra Launch 22SSV - Sold
-
06-13-2020, 08:49 PM #16
Mine has an extra switch labeled AUX for these lights.
Sent from my iPhone using Tapatalk
2018 Moomba Craz
6.2L Raptor 400
6 Pump Ballast, Autowake 2.0, Flow 2.0 Surf System
OJ 15x13 Wake Prop
Digital Cruise Pro 3 (paddle wheel)
Wetsounds Rev 10's
2005 Supra Launch 22SSV - Sold
-
06-13-2020, 10:47 PM #17
Would love to see how they look when completed.
Sent from my iPhone using Tapatalk2016 Mojo
2010 Moomba LSV-Sold
-
06-14-2020, 09:00 AM #18Senior Member
- Join Date
- May 2020
- Location
- Nashville
- Posts
- 225
@jcarter
What light did you use for the Mona logo?
Where did you find the 2 sets of wires? I assume the craz and mojo harness are the same.2018 Moomba MOJO
4100lbs. ENZO's, Center Tank, IBS
780lbs. Lead Wake
Raptor 400
Surf Prop: OJ 945
2019 Ford F150 FX4
5.0L V8
-
06-14-2020, 10:01 PM #19
I removed Moomba emblem and put LED tape light in the top of housing. I just made sure to clean the surface I applied it to really well with alcohol. So far it has stayed in place. I also had a metal shop water jet a stainless steel overlay for the Moomba. Has nothing to do with lighting, but I thought it looked pretty sweet. The wires on my Craz were hanging out of the wiring harness in the rear on the port side. Just remove the cover panel in the back and mine had two leads labeled “Under water lights”.
As for this Fire Water Marine plug light....I am becoming highly skeptical. I went to install it tonight and the threads are not long enough to properly seat the plug. It did not come with an o ring either. I am going to pick one up tomorrow and hopefully be able to make this thing work. I may use some form-a-gasket also. It just makes me nervous that it is going to leak. It won’t be an issue to clear the wake plate though.
Sent from my iPhone using Tapatalk
2018 Moomba Craz
6.2L Raptor 400
6 Pump Ballast, Autowake 2.0, Flow 2.0 Surf System
OJ 15x13 Wake Prop
Digital Cruise Pro 3 (paddle wheel)
Wetsounds Rev 10's
2005 Supra Launch 22SSV - Sold
-
06-15-2020, 08:32 AM #20Mike
2013 Outback V
- ballast: 900# rears / 400# center / 650# IBS
- audio: Exile SXT9Q x 2 towers / Kicker KM65 x 6 cabins / Xi 12 sub / Javelin & XM15.4 amps / ZLD
- FAE
- DIY suckgate
2003 SeaRay 182 -- gone but not forgotten...