Page 1 of 2 12 LastLast
Results 1 to 10 of 11
  1. #1
    Join Date
    May 2019
    Posts
    14

    Default Moomba covers-tower socks

    Hi all,

    Hope everyone is safe and enjoying some social distancing on the water. Question for everyone on covers. Our 2016 Craz cover has an opening that goes around the base of the tower on each side. We have a ton of trouble with water getting through this opening. I've seen several covers with "socks", for lack of a better term, that go up the tower a couple feet. I'm wondering if anyone knows where I can purchase these socks as I've had no luck in my searches. I'm worried that it's attached to the cover and ours simply doesn't have that built into cover. Thanks for the guidance as always friends!

  2. #2
    Join Date
    Aug 2011
    Location
    Commerce Lake, MI
    Posts
    2,128

    Default

    Might have to have them custom made


    Sent from my iPad using Tapatalk
    2017 Moomba Craz

  3. #3
    Join Date
    May 2018
    Posts
    2,151

    Default

    Is there an option for a tower down full cover like Supra offers? If the tower folds, what is the advantage of leaving the tower up and covering the boat?


    Sent from my iPhone using Tapatalk
    2021 Supra SA 400
    2018 Supra SA 400 (SOLD)
    Michigan

  4. #4
    Join Date
    Aug 2011
    Location
    Commerce Lake, MI
    Posts
    2,128

    Default

    No, as the Moomba towers do not lock in the lowered position and would bounce around like crazy.


    Sent from my iPad using Tapatalk
    2017 Moomba Craz

  5. #5
    Join Date
    May 2018
    Posts
    2,151

    Default

    Thanks for clarifying Stazi, makes sense now.


    Sent from my iPhone using Tapatalk
    2021 Supra SA 400
    2018 Supra SA 400 (SOLD)
    Michigan

  6. #6
    Join Date
    Aug 2011
    Location
    Commerce Lake, MI
    Posts
    2,128

    Default

    No worries, Kent.


    Sent from my iPhone using Tapatalk
    2017 Moomba Craz

  7. #7
    Join Date
    Oct 2016
    Location
    Wisconsin
    Posts
    290

    Default

    i have never seen these but would be interested myself. The moomba covers are very hard to get tight around the base of the tower. Almost like they are quite a bit small. Even my dealer couldn't get it tight without gaps. This should be addressed by SC
    2019 Mondo

  8. #8
    Join Date
    May 2019
    Posts
    14

    Default

    Thanks for the thoughts everyone. Looks like it's time to break out the sewing kit for some homemade socks.

  9. #9

    Default

    We have had covers that had these as part of the design. As in all one piece.

    I’ve been frustrated with covers that have a gap around the tower or Bimini—leaves and rain—more than you would expect.

  10. #10
    Join Date
    Feb 2017
    Location
    Ontario
    Posts
    104

    Default

    On my Mondo I ended up putting towels around the tower then put the cover over them. It wasn't a perfect seal, but it definitely helped.

    IMG_4008.jpg

    I was hoping not to with the newly designed cover, but it looks like I'll be doing the same with my Kaiyen.
    2020 Moomba Kaiyen > Finally on my lift!
    2017 Moomba Mondo > Traded
    2000 Moomba Kamberra > Traded

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •