Results 1 to 8 of 8
Thread: Amp Question for 2019 MAX
Hybrid View
-
02-19-2020, 12:55 PM #1Senior Member
- Join Date
- Jun 2016
- Posts
- 288
Amp Question for 2019 MAX
I have a factory stock stereo.
1- 10"sub
2- 8" tower speakers
4- in hull speakers.
The Sub and the tower run off the same wet sounds amp.
I want to add an amp to the in hull speakers.
How should I do this?
What should I buy?
Should I use my existing amp for in hull and then buy 2 amps - 1 for sub and 1 for tower speakers?
I dont want to over think this. Just looking for advice.2019 MAX
2015 Mobius LSV Surf Edition (SOLD)
2001 Supra Sunsport SSV- SOLD
2017 Ram 2500 Crew Cummins 6.7L
-
02-19-2020, 01:05 PM #2
I'm guessing you have a 5ch amp with 4channels bridged to power your towers and a dedicated channel for your sub.
Are you good with 4 in-boats or could you see yourself adding 2 more to the bow?
This answer could drive amp selection.
Sent from my Note9 using Tapatalk2017 Moomba Craz Surf Edition
Flow 2.0 Surf System w/ AutoWake™
5,600 Lbs Ballast - Enzos + Lead + Sumo
Wet Sounds REV10s + REVO12-XXX
-
02-19-2020, 01:30 PM #3
A 2019 would be using Wet Sounds amps I believe, the HTX series? However, I do not know which model Moomba would use to power the woofer and tower speakers, could be the 4 or the 6. In past years, IF the boat was fitted with a woofer, the in-boats were also amp'd along with the woofer. If the boat was fitted with tower speakers, it had its dedicated amp.
2 things I would want to know, before making a suggestion. Which 8" tower speakers, as there are 2 options, and exactly which amp it would be, driving the tower pods and woofer.
-
02-19-2020, 01:45 PM #4Senior Member
- Join Date
- Jun 2016
- Posts
- 288
I am good with just the 4. Hell we get noise complaints already.
This is not my boat or video. but is what I have .https://www.bing.com/videos/search?q...tail&FORM=VIRELast edited by flienlow; 02-19-2020 at 01:47 PM.
2019 MAX
2015 Mobius LSV Surf Edition (SOLD)
2001 Supra Sunsport SSV- SOLD
2017 Ram 2500 Crew Cummins 6.7L
-
02-19-2020, 02:29 PM #5
The boat in the vid, looks to be fitted with a 4 chnl HTX-4 driving the tower speakers on one half and the woofer bridged on the other half. Heres what I would do IF this is the case. Id go with the HTX-6 for the 4 in-boats and move the woofer over to it as well. This frees up the existing 4 chl to just drive the tower speakers in 2 chnl bridge mode. This will be a significant wattage increase for both the tower and in-boat zones. Woofer wattage stays the same.
-
02-19-2020, 02:47 PM #6Senior Member
- Join Date
- Jun 2016
- Posts
- 288
ok, so just buy this and some cable? If this would works, I think it would be the type of solution I am looking for.
https://www.crutchfield.com/p_867HTX...RoCHIwQAvD_BwE2019 MAX
2015 Mobius LSV Surf Edition (SOLD)
2001 Supra Sunsport SSV- SOLD
2017 Ram 2500 Crew Cummins 6.7L
-
04-21-2020, 07:49 AM #7
I just added an amp, and subs to this setup. The stock amp is the HTX-4 (4 channel amp). 2 channels are bridged for the sub, and 2 are bridged for the tower speakers. The in-boat speakers are direct to the radio. I took the sub off the HTX-4, and ran the in-boat speakers to it. They sound so much better.
2019' Moomba Max