Results 11 to 20 of 20
Thread: Adding seat hinges to a Max
-
11-08-2020, 08:11 AM #11
I did what Murder Max did with his......they open to the front......works great and saves the vinyl when my teems would drop them in. I did get a longer hinge then murder did....for more support.
https://www.greatlakesskipper.com/st...o-hinge-single
The opening direction doesn't bother me because my compartments are fill with 1000's and only free for storage when we are not surfing for the day.
On my front cushions....I put a strap in the middle across the opening with a snap on one side. When someone opens it and it wants to fall into the compartment, the strap keeps it from falling in. Again, it saves the vinyl. When you have to put boards or something big in there, undo the snap.
D2022 MAX
Steamboat,CO
-
11-09-2020, 04:10 PM #12Senior Member
- Join Date
- Aug 2017
- Posts
- 143
-
11-09-2020, 05:36 PM #13
-
11-10-2020, 08:27 AM #14
For the front cushions....I positioned the strap a little more to the back of the boat and not centered. I found during my test....that the wider part of the cushion would want to fall in first. And from the few nicks that were from it falling in the compartment...they were more towards the back. Also....make sure the center hull side of the strap is inset enough to not be seen when the cushion is on. I made this mistake on the fronts and had to put the rubber coating spray stuff in white to have it not be seen. The center cushions in the boat (before hinges installed) the straps were installed in the center of the cushion.
D2022 MAX
Steamboat,CO
-
11-10-2020, 09:08 AM #15
-
11-11-2020, 08:26 AM #16
thumbnail-2.jpgthumbnail-1.jpgthumbnail-3.jpgthumbnail.jpg
First Pic: Obviously the strap with the snap
Second: How it looks when you screw up and put the hole to far to the outside edge. (on all the others before the hinges, I place one of the round stickers from office supply place to see if it was covered)
Third: Hinge like Murder Max did, but longer.
Forth: Obviously both hinged and open
FYI: I found the snap set up worked great for cushions falling in (which annoyed me and messed up two cover edges) However, the snap and the screw will put some pressure marks on you upolstry trim strip) Did it effect mine over the summer? No.....however, I was going to and still might experiment as to how I can avoid this in the long term. I do upolstry myself and always figured if there was an issue, I would be able to repair it. But I wanted to express the situation before anyone else did it. I also use screws vs. bolts like I did on the hinges. If a snap breaks, very easy to repair and put a new snap on...same location. Maybe all this helps......maybe not but it solved my stress with the teens constantly going in the compartments....especially friends who didn't know the system.2022 MAX
Steamboat,CO
-
09-13-2023, 02:43 PM #17
Found this on youtube, who is this guy I need to know what hinges he used. This is perfect!
https://www.youtube.com/shorts/enT1u-WHbOE2023 Moomba Max
5,550lbs ballast | 1,000lbs lead = 6,650lbs
2014 Moomba Mojo 2.5- SOLD
Tow- 2002 F-350 Super Duty 7.3L PSD
-
09-13-2023, 03:53 PM #18
If I am not mistaken, he made the hinges. He made the brackets/supports out of angle iron.
Sent from my SM-G975U1 using Tapatalk- Jason
2019 Moomba Max
-
09-13-2023, 06:08 PM #19
He made the supports for the hinges. The hinges appear to be malibu/axis hinges.
2015 Moomba Mojo Surf Edition
4,000lbs
Manual Flow
-
09-14-2023, 06:24 AM #20