Results 1 to 9 of 9
  1. #1
    Join Date
    Jun 2017
    Location
    Pendleton, Indiana
    Posts
    107

    Default Mooring cover cleat access? Please help me find these?

    Hello!

    I use my factory mooring cover regularly but have been rather frustrated that it doesn’t allow access to the mooring cleats! Doesn’t make much sense to me that Moomba calls this a mooring cover but doesn’t accommodate access to the cleats!

    Here is a pic of my pier setup but as you can see in order to tie the boat up I have to run the dock lines and fender lines down under the cover and over to the tie up points but this doesn’t allow me to sinch up the mooring cover tight enough under the rub rail as it should be. When it gets windy I get worried that the wind will get in under the cover and blow it off since I can’t get it tight under the run rail.



    Axis and a few other Manufactures includes these access hatch style access points in there factory covers...




    Does anyone know where I can find these to buy by themselves????

    All I can find are just these rubber reinforcements but I see a lot of manufacturers use the other hatch style???



    I would like to just by the hatches and take them and my cover to a local canvas/upholstery shop and have them installed into my factory cover but for the life of me I can’t find that nicer hatch style one???

    -Tyler
    Last edited by Tylerrnemt; 08-09-2019 at 10:13 PM.


    2012 Mobius LSV (Sold)
    2020 Mojo

  2. #2
    Join Date
    Nov 2010
    Location
    Katy, TX
    Posts
    6,368

    Default

    I tried to find these as well as the one that covers the fuel fill and had no luck. I don't understand why it is so difficult. Maybe contact whoever makes those particular covers.
    David

    2017 Moomba Mojo Max Surf Edition, 2 Pair Wetsounds Rev10s powered by an SD2, 6 pair Wetsounds XS650M and Wetsounds XS12 powered by SD6 all controlled by a WS420. 2 Lumitec SeaBlaze X2 Spectrum underwater lights

    SOLD***2008 Mobius LSV, Gravity III , Wake Plate, Z5, Exile SX65c's, Exile XM9s, Exile XI12D, Exile Javelin, Exile 30.2***SOLD

  3. #3

    Default

    https://www.etsy.com/listing/1477539...?gpla=1&gao=1&

    This is the only thing I have found
    2023 Moomba Max
    5,550lbs ballast | 1,000lbs lead = 6,650lbs
    2014 Moomba Mojo 2.5- SOLD
    Tow- 2002 F-350 Super Duty 7.3L PSD

  4. #4
    Join Date
    Jan 2021
    Location
    Columbus, Ohio
    Posts
    1,251

    Default

    Not sure about the new covers. My 2015 cover has access for the cleats. Also have a zippered access forbthe full door.

    Wonder why Skiers would have changed that?
    2015 Moomba Mojo Surf Edition
    4,000lbs
    Manual Flow

  5. #5
    Join Date
    Mar 2021
    Location
    South Georgia
    Posts
    1,953

    Default

    This is the factory cover my 2021 Makai came with. It has a stitched in overlapping style flap over each cleat. Similar to the fly on a pair of whitey tighty underwear to simply describe them. There is one up front too, just not in the picture. They are on both sides of the boat. You might be able to have an upholstery shop cut something like that into your existing cover. No zippers to ever go bad that way, and they lay down flat when not using them.

    Sent from my SM-G781V using Tapatalk
    Last edited by HFarr; 05-31-2023 at 08:31 PM.
    2021 Moomba Makai
    Black Cherry Metal Flake & Fire Red
    Nibral OJ 15.5x15 Altitude/Wake prop w/1.76 trans v-drive
    Wet Sounds bow speakers & 10's on the Tower & ported sub

  6. #6

    Default

    Yea thats how all the newer moombas are in my marina but in 2014 we did not get the flaps like that.
    2023 Moomba Max
    5,550lbs ballast | 1,000lbs lead = 6,650lbs
    2014 Moomba Mojo 2.5- SOLD
    Tow- 2002 F-350 Super Duty 7.3L PSD

  7. #7

    Default

    In my experience, I have found the factory covers from many of the boat manufacturers are lacking. We ended up hiring a semi-local guy that kept the boat for a week. Cost about $1600 but the fit and quality is excellent.

  8. #8
    Join Date
    Mar 2021
    Location
    South Georgia
    Posts
    1,953

    Default

    Got any pictures?

    Sent from my SM-G781V using Tapatalk
    2021 Moomba Makai
    Black Cherry Metal Flake & Fire Red
    Nibral OJ 15.5x15 Altitude/Wake prop w/1.76 trans v-drive
    Wet Sounds bow speakers & 10's on the Tower & ported sub

  9. #9

    Default

    Quote Originally Posted by ejj View Post
    In my experience, I have found the factory covers from many of the boat manufacturers are lacking. We ended up hiring a semi-local guy that kept the boat for a week. Cost about $1600 but the fit and quality is excellent.
    Interesting I can get a whole new cover from evolution covers for about $1000
    2023 Moomba Max
    5,550lbs ballast | 1,000lbs lead = 6,650lbs
    2014 Moomba Mojo 2.5- SOLD
    Tow- 2002 F-350 Super Duty 7.3L PSD

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •