Results 1 to 10 of 14

Thread: Surf Plate

Hybrid View

  1. #1
    Join Date
    Jul 2017
    Location
    Columbus, GA
    Posts
    84

    Default Surf Plate

    Anyone had any issues with the surf plates not switching correctly? I couldn't figure out why my goofy wave was so washed out. Turns out the plate wasn't deploying completely. Only solution I've found is to turn the battery switch off and back on. Boom, goofy wave appears again. It's done this now 3 times. Any ideas what could cause this or things I need to check?
    17' Craz

  2. #2
    Join Date
    Jul 2017
    Location
    Columbus, GA
    Posts
    84

    Default

    Quote Originally Posted by ATS0921 View Post
    Could be wrong but I think they default to the last setting if you change them manually.

    Sent from my SM-G965U1 using Tapatalk
    Correct, but when I hit the switch to change from regular to goofy, either the port side plate isn't rising or the starboard plate isn't deploying as it should. On the display screen it changes correctly, but you can tell by the wave that's its not. Once again, when I kill the battery and start over. It works fine for awhile and I have a great wave on either side...
    17' Craz

  3. #3
    Join Date
    Jun 2018
    Location
    Nor Cal Central Valley
    Posts
    34

    Default

    My Mojo Pro does the same. Sometimes my goofy is completely washed, like impossible to surf. I can switch surf to port, wait a few second, then switch back and most of the time it works. Switching too fast sometimes wont work either. Not sure what it is, ut its something with the surf tabs. the first couple times I pulled the boat out of the water and watched the plates.
    2018 Mojo Pro
    Intense Green

  4. #4
    Join Date
    Aug 2011
    Posts
    2,522

    Default

    Quote Originally Posted by 2018MojoPro View Post
    My Mojo Pro does the same. Sometimes my goofy is completely washed, like impossible to surf. I can switch surf to port, wait a few second, then switch back and most of the time it works. Switching too fast sometimes wont work either. Not sure what it is, ut its something with the surf tabs. the first couple times I pulled the boat out of the water and watched the plates.
    Did you update the firmware? There was a bug that the plate didn't deploy sometimes.
    http://www.instgram.com/jlyons30
    2002 Moomba Mobius LSV - Sold
    2006 Moomba Mobius LSV - Sold
    2017 Moomba Craz - Enzos, Lead

  5. #5
    Join Date
    Apr 2019
    Location
    Northern California
    Posts
    19

    Default

    I have a similar issue with my 19. Dealer rolled firmware back recently to see if it corrected. While it appears to have corrected loss of control over the surf plates, I think the system is now ignoring/isn’t aware of the ballast bag pressure sensors.
    My dealer has assured me that SC is working on my particular issue.
    I had a firmware date of 9/2018 originally & currently loaded firmware date of 7/2018.
    2021 TBD
    2019 Moomba Mojo - Sold
    1994 Champion - Sold
    1991 Ski Brendella - Sold

  6. #6
    Join Date
    Aug 2011
    Posts
    2,522

    Default

    Quote Originally Posted by Saclsick6 View Post
    I have a similar issue with my 19. Dealer rolled firmware back recently to see if it corrected. While it appears to have corrected loss of control over the surf plates, I think the system is now ignoring/isn’t aware of the ballast bag pressure sensors.
    My dealer has assured me that SC is working on my particular issue.
    I had a firmware date of 9/2018 originally & currently loaded firmware date of 7/2018.

    Think you may have a different screen than us Craz people? I've been using the lastest from Matt, 02/2019..

    Moomba_MY20_HV480_2810533_20190213.gciBin
    http://www.instgram.com/jlyons30
    2002 Moomba Mobius LSV - Sold
    2006 Moomba Mobius LSV - Sold
    2017 Moomba Craz - Enzos, Lead

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •