Results 1 to 10 of 10
-
06-01-2019, 10:12 AM #1Junior Member
- Join Date
- Apr 2017
- Location
- Mandeville, LA
- Posts
- 9
Lead weight placement for 2017 Mojo
I now have 500 lbs of lead and trying to figure where to put them all so I don’t have to move them around.
I have both goofy and regular surfers.
I currently have a 2017 Mojo surf edition with the stock 3000 lbs.
900’s in rear, 700 in middle and 500 in bow.
Thanks for any advice
🤙🏽
-
06-01-2019, 10:36 AM #2
Lead weight placement for 2017 Mojo
I am also adding 500lbs to my 2017 mojo, although I have the Enzo sacs in the rears. I have been told the lead should all go in the bow, but I haven’t tried it yet.
'08 Mobius LSV- SOLD!
2017 Mojo Pro
-
06-01-2019, 10:59 AM #3Junior Member
- Join Date
- Apr 2017
- Location
- Mandeville, LA
- Posts
- 9
How big are the enzo’s? Maybe I’ll
Put some in back and bow.
-
06-01-2019, 11:00 AM #4
The Enzo sacs are 1450 each. They fill the rear compartments almost completely.
'08 Mobius LSV- SOLD!
2017 Mojo Pro
-
06-01-2019, 11:06 AM #5Junior Member
- Join Date
- Apr 2017
- Location
- Mandeville, LA
- Posts
- 9
No issues with the panel bending? Mine has with the 900lbs
-
06-01-2019, 11:54 AM #6
An alternate to the enzos is to use two of the standard 400 lb bags under the cabin seats and just using a tsunami pump to fill and drain them. This is what I do and when the bags are empty I just put stuff on top of them when I need that space for storage and just use the 900s in the rear. I only have 200 lbs of lead and am moving it all over all the time but when we surf (goofy) I usually put two behind the driver seat and one on either side of the v-drive cover.
David
2017 Moomba Mojo Max Surf Edition, 2 Pair Wetsounds Rev10s powered by an SD2, 6 pair Wetsounds XS650M and Wetsounds XS12 powered by SD6 all controlled by a WS420. 2 Lumitec SeaBlaze X2 Spectrum underwater lights
SOLD***2008 Mobius LSV, Gravity III , Wake Plate, Z5, Exile SX65c's, Exile XM9s, Exile XI12D, Exile Javelin, Exile 30.2***SOLD
-
06-01-2019, 12:02 PM #7
-
06-03-2019, 08:46 AM #8Junior Member
- Join Date
- Apr 2017
- Location
- Mandeville, LA
- Posts
- 9
Yes it has metal. It bends and popped one of those blots already
-
06-03-2019, 04:18 PM #9
The 1100’s I had did the same thing. But the Enzo’s IMO fit much better and don’t bulge the sides. As far as the lead is concerned I ran 250 in the bow and 250 on the surf side made the wave much longer but also had to watch for rollers a lot more
Sent from my iPhone using Tapatalk2015 Mojo
2005 Yamaha at-230 sold
2012 Ram 2500 tow rig
-
06-03-2019, 05:06 PM #10Member
- Join Date
- Jan 2014
- Location
- Canby, OR
- Posts
- 68
I have the Wakemakers Custom Fit Bags (1475# or so) and they eventually sheared off the plastic C-channel that the engine panels slid into at the floor. Side note, I re-purposed a Wakemakers engine divider panel saver kit I had laying around by using the aluminum C-channel in the kit to replace the plastic channel that came stock with the boat. Worked great, C-channel is the perfect size.
2017 Mojo (sold)
2005 Moomba XLV (sold)