![Moomba on Facebook Moomba on Facebook](/assets/images/chicklet_facebook.gif)
![Moomba on Twitter Moomba on Twitter](/assets/images/chicklet_twitters.gif)
![Moomba on Vimeo Moomba on Vimeo](/assets/images/chicklet_vimeo.gif)
![Moomba on Instagram Moomba on Instagram](/assets/images/chicklet_instagram.gif)
![Moomba on Blogger Moomba on Blogger](/assets/images/chicklet_blogger.gif)
Is there someone that already installed surf tabs on a direct drive boat (ski boat)? I have a Supra Launch LTS 2004 boat and I would like to add some home made automatic tabs to improve the wave. Currently, with 800 lbs in the front and 1200 lbs in the back, I am able to surf but I would like to improve my wave without buying a new V-drive boat.
Thanks
Eric
Not many people looking to spend $3-4K on tabs for a boat when most d-drives can be worth 20k?
Not saying you have a 20k boat, but I do not think you will find many on those hulls.
Sent from my iPhone using Tapatalk
2018 Supra SL400
Good for you if you can make home made ones and save the $$.
Sent from my iPhone using Tapatalk
2018 Supra SL400
It is definitely do-able.
Here is a thread on a homemade system.
https://forum.moomba.com/showthread....ight=Surf+tabs
Wakemakers sells a kit.
https://www.wakemakers.com/go-surf-a...QaAhyCEALw_wcB
I’m pretty sure these could be modified, depending on how handy you are.
https://www.iboats.com/shop/lenco-12...UaAkVpEALw_wcB
-Blaine
2019 Makai
2013 LSV (sold)
1997 Bayliner 1850 (sold)
Thanks guys. I already read those thread (well done shoebox btw, it's awesome) but i couldn't find anything for direct drive boad.
;
I decided to go ahead and give it a try. Here is the design i will was thinking to install :
gate_1.JPG
gate_2.JPG
Attachment 27988
gate_3.JPG
Undeployed it's -15 degrees and it will go up to 30 degrees fully deployed.
I will be using the lenco 101 XDS actuator (already ordered) and i will be controlling this with an Arduino MEGA so i can hook it up to a screen and a GPS module. This way I can program some automation (auto retraction after X mph, etc.).
Since i don't want to drill my hull, i will make an aluminium structure that will be attached to the swim plate brackets. My swimming plate is very low with all the extra weight i put in the back so i will use a 2'' Aluminium C beam to jack it up and i will also attach my surf tabs structure on it.
I am from Montreal so i have about 5 months to get this done before i can give it a try so that should give me plenty of time.
Any thoughts ?
You're going to have to drill into your hull to mount the tabs, so why not a couple more holes for the actuator? It would save a ton of time and effort.
It looks great, a lot like the Mastercraft tabs. That outward angle should probably make for a great wave, since you're getting a little tab effect, and a little gate effect.
As I mentioned in my write up, I'd recommend tapping the hinge holes and use machine screws, not sheetmetal screws, unless you have access that you can through-bolt.
2019 Supra SL450
Does your swim platform interfere with your wake?
Sent from my iPhone using Tapatalk
2018 Supra SL400
I did a surf system like Nautique's NSS on my Direct Drive. It worked pretty well. It was actually cost effective and I could change sides in under 30 seconds manually.
https://forum.supraboats.com/showthr...-after-the-NSS
2008 Moomba Mobius XLV. Monster Cargo Bimini, WS Rev 410's, Polk Cabins, 3 Infinity Subs, PPI amps, WS420, Exile BT, upgraded ballast pumps, up to 3,500+ pounds of ballast, Blue LED's...
1992 Supra Sunsport. **SOLD** 2k pounds ballast, Surf System, Blue LED's everywhere, decent audio system.
Tow Rig: 2013 F150 Ecoboost FX4 (wife's rig) Other money pits include:1998 BMW M3 Cabriolet, 2009 Audic A6 Avant 3.0T, 2005 Kawasaki ZX-6R 636.
www.TraysonsToybox.com
Save your money and time and use a suck gate or ghetto gate.
http://www.instgram.com/jlyons30
2002 Moomba Mobius LSV - Sold
2006 Moomba Mobius LSV - Sold
2017 Moomba Craz - Enzos, Lead