Results 231 to 240 of 268
Thread: Murder Max Mods
-
05-05-2021, 09:50 PM #231
Getting there....
Of course I forgot some tools I needed so I couldn’t finish but it’s getting there. Getting the tubing on sucks lol.
2019 Moomba Max "MOOMBAE"
Mods: Wakemakers upgrade + 500 lbs of lead
2016 Yamaha AR192 - sold
-
05-06-2021, 09:48 AM #232
-
05-06-2021, 01:22 PM #233
Yes it’s 1”
2019 Moomba Max "MOOMBAE"
Mods: Wakemakers upgrade + 500 lbs of lead
2016 Yamaha AR192 - sold
-
05-07-2021, 10:46 AM #234
Added some rubrail docking lights to the boat last week before taking it up to the lake. I used these: https://www.itc-marine.com/product/led-rubrail-light/
Warning: cutting the rubrail out is not for the faint of heart. I used a combination of a dremel, angle grinder with cutoff wheel, and hacksaw to make the cut.
For the wiring I found the spade connector for the heater fan “high” in the harness under the helm and ran positive to that(since I don’t have a heater), and ground to the negative bussbar under there.
Here’s some pics
2018 Murder Max
2008 Outback V-Bought new; sold in 2018
-
05-07-2021, 11:04 AM #235
Was it necessary to cut the rub rail?
The specs show them mounting over top the rail. I know to get wires and such into the boat you have to do something, but I figured just remove a screw and enlarge the hole.
I am probably missing something here, but you do have Kahunas and patience to get that done. The look great, good job.2015 Moomba Mojo Surf Edition
4,000lbs
Manual Flow
-
05-07-2021, 11:15 AM #236
It wouldn’t be flush mounted without cutting the rubrail.
2018 Murder Max
2008 Outback V-Bought new; sold in 2018
-
05-07-2021, 03:27 PM #2372015 Moomba Mojo Surf Edition
4,000lbs
Manual Flow
-
05-08-2021, 12:17 PM #238
Yes interested to hear how the seat riser has been performing. I wouldn’t mind adding one to mine so that I don’t have to use the bolster on rougher days.
If I boated at night often or lived on the lake I would be installing those LEDs. I’ve seen others install them and they look right at home on the Max IMO.2019 Moomba Max "MOOMBAE"
Mods: Wakemakers upgrade + 500 lbs of lead
2016 Yamaha AR192 - sold
-
05-08-2021, 05:11 PM #239
We love the seat pedestal! In fact we leave it at its tallest position all the time so really no need for it’s adjustability. Funny you mention reading about the pin because once in a blue moon the damn thing will drop all the way down for some reason, but hasn’t since I used a wrench to get the pin really tight.
2018 Murder Max
2008 Outback V-Bought new; sold in 2018
-
05-09-2021, 09:27 AM #240
@Murder - Did you use the 50 or the 80 mil Kilmat? Also, what tape did you use for the edges? How did you decide to lay each square to get the most use of the mat?
Current Boat: 2021 Moomba MAX, 400 Raptor, G6 Ballast
Prior Boats:
2015 Nautique G21
2012 Mastercraft X45
2010 Mastercraft X14V
2005 Sea Ray 220SEL
1986 Mastercraft 190