Results 1 to 10 of 30
Thread: Installed Indmar sea strainer
Hybrid View
-
07-10-2017, 02:52 PM #1
Installed Indmar sea strainer
I was able to get rid of two 90 degree bends. One on the stock strainer is gone and the one coming up through the hull is gone. My through hull had a 90 attached to it with NO seacok. I added the seacok, new hoses and the strainer.
I found that it is running a decent bit cooler, maybe 15-20 degrees on average. I think getting rid of those 90 degrees plus the larger through put volume of the Indmar strainer has increased flow. I have noticed this since I installed it over a month ago. It seems to be working well.
The only down side is I am not sure how you empty it while in the water without spilling it while on the water. I put it on my lift to empty it because all of the water drains down and out so no problem. You can't remove the "bowl" part but you can put a container under it to catch the water. Does anyone have a good solution for that?
The screen comes out easily. I haven't used the flush fitting but I am REALLY looking forward to not having to climb under the boat with the toilet plunger again.2007 XLV Gravity Games
Full Wake Makers upgraded ballast and pumps
1,100 in each rear locker
1,180 in front
OJ 1435 prop, 325 EFI Indmar Assult.
Fresh Air Exhaust
SuckG8
Bunch of other crap
-
07-10-2017, 03:30 PM #2
Have pics?
Do you have the 340 CAT/ETX or the 325 Assault?2007 XLV Gravity Games Edition
340HP CAT/ETX
ACME 1235 / Fresh Air Exhaust
1180 Front, 1100s Rear, 400 under Surf Side Seat, Homemade Suckgate, Custom Surf Platform
Slingshot Hooke, Doomswell Neo, Phase 5 Hammerhead, Parker Surfcraft Phantom
-
07-10-2017, 04:22 PM #3
I don't. I won't see the boat for the next two weekends. It is horizontal over the V-drive. Really limited as to how I could mount it but it seemed like the best way to go. The only other option would be for the intake side to point down and that would be tough to catch the water rather than just let it in the bilge. It really isn't that big a deal, there is only about a cup of water in that filter anyway.
Do these boats not come with seacoks at all or was mine removed?2007 XLV Gravity Games
Full Wake Makers upgraded ballast and pumps
1,100 in each rear locker
1,180 in front
OJ 1435 prop, 325 EFI Indmar Assult.
Fresh Air Exhaust
SuckG8
Bunch of other crap
-
07-10-2017, 05:15 PM #4
Is it this one? http://www.indmar.com/mobile/experie...ion_Award.aspx
Funny that the part itself has 1 x 90 deg bend. I would like to do one of these. I always hate sliding under the trailer with the plunger.2007 XLV Gravity Games Edition
340HP CAT/ETX
ACME 1235 / Fresh Air Exhaust
1180 Front, 1100s Rear, 400 under Surf Side Seat, Homemade Suckgate, Custom Surf Platform
Slingshot Hooke, Doomswell Neo, Phase 5 Hammerhead, Parker Surfcraft Phantom
-
07-10-2017, 06:29 PM #5
That is the one. Some people are using the Perko Flush Pro Valve for flushing. For boats without the seacok that is the way to go as it automatically stops flow out of the inlet on the bottom of the hull; but you still need the strainer. I wanted to have a shutoff on there in case there was some catastrophic cooling system failure.
I could have done without any 90* bends as that actually made it more difficult for me plus is is just more resistance in the system but I am sure that was compensated for. I just have an aversion to 90* bends
I am with ya! I am so looking forward to not crawling under there and having to adjust the plunger when it moves withe water on the ground at the end of October.2007 XLV Gravity Games
Full Wake Makers upgraded ballast and pumps
1,100 in each rear locker
1,180 in front
OJ 1435 prop, 325 EFI Indmar Assult.
Fresh Air Exhaust
SuckG8
Bunch of other crap
-
07-10-2017, 08:10 PM #6
Mine does not have a seacock on that thru-hull. Did you just splice it into that main intake line?
20170710_234223067_iOS.jpg2007 XLV Gravity Games Edition
340HP CAT/ETX
ACME 1235 / Fresh Air Exhaust
1180 Front, 1100s Rear, 400 under Surf Side Seat, Homemade Suckgate, Custom Surf Platform
Slingshot Hooke, Doomswell Neo, Phase 5 Hammerhead, Parker Surfcraft Phantom
-
08-16-2017, 11:55 AM #7
What is the oil temp?
As long as it goes to 212 or slightly above.
Moisture must be eliminated in the crankcase.
Sent from my iPhone using Tapatalk Pro2008 Moomba Outback DD resurrection
-
08-17-2017, 08:39 AM #8Senior Member
- Join Date
- Apr 2013
- Location
- Richmond, VA
- Posts
- 123
I installed the new sea strainer last year and it is absolutely worth the $100. Very easy to run off the hose now.
I did have to cut off part of my intake hose to make it fit but that was fairly easy to do with a hacksaw.2017 Axis T23
2014 Supra SC350 Sold
2012 Outback V - Sold
-
01-26-2018, 10:43 AM #9Junior Member
- Join Date
- Apr 2017
- Location
- Columbus, OH
- Posts
- 21
Looking for directions on what this would take to install on CAT 340, the indmar one with the hose attachment. Thanks
2018 SR450
**Previous**2009 Supra Launch 22SSV
-
01-27-2018, 03:35 PM #10
Is this the one?
http://www.mastercraft.com/teamtalk/...ad.php?t=72593
Sent from my P00I using Tapatalk2018 Supra SL400