Results 111 to 120 of 173
Thread: July 2017 Picture thread
-
07-20-2017, 01:25 PM #111
Pretty sure the Camber board is a keeper. Effortless pop off a DD and Ollies r solid too. He said the landings also felt much smoother. Tomorrow he gets to ride behind a 211. Should be a great day!!!!
Sent from my iPhone using Tapatalk2003 Moomba Outback with 283 hrs on the 310HP Indmar. Its in Cherry condition also and now we will again start to use the boat after a few years off.
-
07-21-2017, 10:30 AM #112Member
- Join Date
- Aug 2015
- Location
- DFW
- Posts
- 41
-
07-21-2017, 10:44 AM #113
Sent from my iPhone using Tapatalk2020 SA ?,2019 SE550
2018 G23 sold
2017 SE450,2016 SA400 Sold
2015 MB B52 23,2012 MB F21 Sold
2014 Axis A22, 2010 Axis A22 Sold
2018 Ram 2500
-
07-21-2017, 01:45 PM #114
Finally, don't like the three extra bags on the seats and floor, but.... that wave...
Sent from my SM-G930V using Tapatalk2017 Centurion Ri237
2013 Supra SA450 - Sold
2006 Mobius LSV - Sold
2004 Stingray 190LS - Sold
2016 Nissan Titan XD - Tow Rig
-
07-21-2017, 01:56 PM #115
Been doing a lot of garage boating working on a ballast system upgrade. I have about 1 hour left. So far I've added 2 reversible pumps to go along with one I installed a few years ago, tied in the ski locker bag with the bow bag, made the old drain line the vent for this system, upgraded to 1" hose/fittings, added vents for the rear bags (original g1 system so had to drill and add thru hulls), cut a hole to mount the switches, and added 3 timers. It's going to be nice to just flip switches and chill when it's time to fill and empty!!!
2018 Murder Max
2008 Outback V-Bought new; sold in 2018
-
07-21-2017, 01:58 PM #116
July 2017 Picture thread
^brackets I made with some diamond plate stock to mount the pumps
Made quite a mess lolLast edited by z28ke; 07-21-2017 at 02:00 PM.
2018 Murder Max
2008 Outback V-Bought new; sold in 2018
-
07-21-2017, 03:00 PM #117Member
- Join Date
- Aug 2015
- Location
- DFW
- Posts
- 41
I'm in the process of upgrading my ballast pump system too, fun times!
Tonight I'll be fabricating the bracket to mount a pump to the v-drive/transmission and drilling holes in the hull *cringe*.
I'm considering buying those timers as well so I don't have to worry about burning up the impellers.
I don't like the idea of bare hose clamps next to my bags, so I found some 1.5" heat shrink tubing.
2006 Moomba XLV
Indmar 325 MPI - Acme 1433
1,100lb V-drive sacs + 1,180lb front
WakeMAKERS Ballast System Upgrade
DIY SuckGate
PerfectPass DBW
-
07-22-2017, 08:13 AM #118
Looking good zd!!!
2018 Murder Max
2008 Outback V-Bought new; sold in 2018
-
07-22-2017, 01:12 PM #119Senior Member
- Join Date
- Mar 2012
- Location
- Uniontown, oh
- Posts
- 263
-
07-22-2017, 01:14 PM #120Senior Member
- Join Date
- Mar 2012
- Location
- Uniontown, oh
- Posts
- 263