'17 Craz Audio Questions.

[Rakkasan]

Remember this is not the A3 wiring diagram. They have not published that yet.

On my Craz there's are 8 speaker wires coming out the port leg of the tower.

Then the light wires comes out the starboard leg.


Sent from my iPhone using Tapatalk

Do you know what gauge the speaker wire is. I'm sure it's 16ga as that's all the info I'm seeing online. Everyone keeps saying for the REV10 you should use at least 14 even better would be 12. Wanting to do things right the first time is it worth the trouble to upgrade the wiring. I'm sure it's not hard, just tape the new wire to the old and pull the old wire.

[beat taco]

Do you know what gauge the speaker wire is. I'm sure it's 16ga as that's all the info I'm seeing online. Everyone keeps saying for the REV10 you should use at least 14 even better would be 12. Wanting to do things right the first time is it worth the trouble to upgrade the wiring. I'm sure it's not hard, just tape the new wire to the old and pull the old wire.

Yes pull some 12 for the ideal setup. I'm not going to lie though my Supra was 16ga and I'm sure no one could tell!

Sent from my SM-G930V using Tapatalk

[Stazi]

Wires looked like 16ga


Sent from my iPhone using Tapatalk

[beat taco]

Wires looked like 16ga


Sent from my iPhone using Tapatalk

I meant to this day it's running that way

Sent from my SM-G930V using Tapatalk

[Stazi]

Hey guys,
I emailed Roswell and asked them to send me the wiring diagram for the A3 aviator tower on all of the new 2017 Moombas.

I'm pretty sure that some of you guys were thinking I was talking out of my butt when I said there were extra wires for the speakers, in this new A3 version, and this picture that I am attaching confirms it.

Perhaps the moderators want to save this picture in the archives for future use for other people that end up with the A3 tower.




Sent from my iPad using Tapatalk

[kaneboats]

Looks good. Will add to a sticky info thread.

[Jceclipse01]

Knu here also for wiring. 12g to the sub. 4g on amps. The tower should already be wired, same with in boats.

Volt meters next to the switch on a panel above the battery compartment (under the small cushion) ....



Sent from my SM-G928V using Tapatalk

Where did you get those digital voltmeters from?

Sent from my SM-G900V using Tapatalk

[KG's Supra24]

Where did you get those digital voltmeters from?

Sent from my SM-G900V using Tapatalk

https://www.amazon.com/Stinger-SVMR-...+voltage+meter

They also have blue ones.

[Rakkasan]

Ok guys, I've been looking at distribution blocks, in line fuse holders, circuit breakers, power cables, ground cables, Perkos, AND ON AND ON AND ON......

Think I might be overthinking things for my application. I came across the pic online that shows the stock amp board from a 2016 Craz with the bow speaker amp upgrade( same as I getting, probably.) I looks like the Kicker amp is getting power from a stock distribution block with a 8ga wire and inline fuse.

Question: Can I run my SNY-4 from that block using a 4ga and inline fuse?

Sure would simply my setup and save on rewiring everything until I decide to put the second battery and third amp with sub in.

[BigOrange]

I'm going to piggyback on this latest post......so I think I have same distro block and wiring to the factory KX200.2 in my Mojo. My current change to Exile 30.2 (tower) and Javelin (cabin + sub) calls for 4 AWG wire for hot and ground. If Rak is correct that the factory is 8 AWG, looks like I need all new. Can I power off of that distro block with no issues? IS the supply wires to the distro block from battery / perko sufficient?