Results 21 to 30 of 33
-
02-19-2017, 03:47 PM #21Senior Member
- Join Date
- Nov 2014
- Location
- Columbus, Ohio
- Posts
- 388
Thanks MLA. I was messing with everything last night and guess wasn't really awake. I've only used the clamps on prior speakers so didn't realize I had to disassemble the speaker to swap out mounts.
Got it figured out and one speaker on the tower already. I'd have called the vendor except with it being Sunday I figured I'd be SOL until Monday. Appreciate the help.Boatless for now
-
02-23-2017, 12:28 AM #22Senior Member
- Join Date
- Nov 2014
- Location
- Columbus, Ohio
- Posts
- 388
I've got an amp wiring question now.
I've got everything installed and wired up, however I'm only getting sound out of 1 tower speaker. I haven't installed a stereo system in a few years so I'm a bit rusty, and I don't think I've ever bridged an amp before.
I have a PPI 900.4 to a pair of Rev10's. I believe, according to everything I've read including the manual, that I must bridge the 4 channel amp into 2 channels. To bridge the amp I connect the -L to the +R for one speaker and opposite for the other speaker, right? And then I have to have the switch on the amp on ST and hook the RCA's up to the front channel, right?
Am I missing something or doing somethig wrong? If not I guess I need to determine if I have a wiring issue between the amp and speaker, or if I have an amp issue with the channel wired to the speaker that doesn't work.
Lastly, any recommendations on amp settings to start with?
TIABoatless for now
-
03-09-2017, 07:26 PM #23
-
03-10-2017, 02:17 AM #24Senior Member
- Join Date
- Nov 2014
- Location
- Columbus, Ohio
- Posts
- 388
I did....it just took finding the correct page of instructions, lol! It was late and I had been drinking a bit....oops. All is well now. I can grab a few photos up close but they are mounted to the factory location as if you were to order the boat with Rev10's.
You need the X-Mount kit for the speakers and this bracket and they just bolt together as they are supposed to.Boatless for now
-
03-10-2017, 07:11 AM #25
Awesome. I bit the bullet and ordered the speakers with xmount and the adapters last night.
2008 LSV on the way out
'17 CRAZ!!! on the way in
-
03-10-2017, 08:11 AM #26Senior Member
- Join Date
- Nov 2014
- Location
- Columbus, Ohio
- Posts
- 388
-
04-29-2017, 10:13 PM #27
Here is a pic of a custom mount for the rev 10 I did on my 17 Craz, had the same feeling of not wanting to see any wires , but I liked where they sit on the welded plates , worked out pretty cool
rev10mount.jpg
rev10mount2.jpg2017 Craz surf auto wake
1140 # rears wet sounds
-
08-05-2019, 03:32 PM #28
I'm not seeing a link in any of your other posts for pictures. Did you ever get around to posting any? I just brought some Rev10's home for my '19 Craz and was pretty disappointed at how the swivel clamps looked (not mounted on the tower yet). I got the impression the factory mount had a cleaner look? I assumed they mounted them to the plate with three holes in it? Does that sound right?
I would appreciate any advice/pictures you can share!
Thanks!
-
08-05-2019, 05:15 PM #29
@ktenan12,
Those flat spots with 3 holes are a tower pod mounting location, but it seems SC is supplying the speakers using the TC3-S clamps on the bar.
All you need is the CC-FC5U mounts and then you can mount your pods in those locations using the swivel clamps you have.
-
08-05-2019, 05:39 PM #30
Thanks MLA.
You’re talking about this correct?
https://www.wetsounds.com/product/ADP-Nautique-FC5-U
Although I think some other vendors had it in a polished finish which would match what I have better.