Results 11 to 20 of 27
-
09-04-2015, 04:28 AM #11
Sure would be nice to see if this 2.0 would fit on my 13 LSV... I really don't want to upgrade to a Craz and lose my ass on my boat in resale...
2013 LSV Red/White
1100lb upgrades in each rear locker!
Stock 500 Bow ballast
650IBS
Manual Flow equipped
Boards
Hyperlite Hi-Fi "The Illest"
CWB AMG Carbon
Phase 5 Razz
Byerly Volt
4.6 Ronix Koal Fish
Phase Five Scamp (kiddos)
-
03-14-2016, 12:13 AM #12
So did anyone figure out if older boats can do this? Just got a 2008 XLV last fall and want to do this if possible. Let me know!
Jason - 2008 Mobius XLV
Wakemakers wave control surf system
Gravity 3 ballast system
1180 center bag
2 rear 1100 bags
Perfect pass gps
Stazigate 2.0
-
07-08-2016, 12:34 PM #13
Old thread but I can tell you my NEW Craz with 20 hours has problems with the wave coming and going like the electronics stop intermittently. Someone is out surfing, the wave just disappears, then come back, and at the same time trim adjustment quits working, them comes back. At the dealer now except they are telling me 3 weeks out to look at it. NOT happy with that. When the system worked I was pretty happy with the wave. Got about 30 minutes of good waves before it started acting up. At first just starboard side was acting up (only 1 of 5 of us surf that side) then second day started acting up on port side too.
2016 Craz Surf Addition
The Purple Blurrrrrr
-
07-08-2016, 05:55 PM #14
Upgrading the AutoFlow to the new 2.0
My suck/surf tab never lets me down. 😉
Sent from my iPhone using Tapatalk2013 LSV Red/White
1100lb upgrades in each rear locker!
Stock 500 Bow ballast
650IBS
Manual Flow equipped
Boards
Hyperlite Hi-Fi "The Illest"
CWB AMG Carbon
Phase 5 Razz
Byerly Volt
4.6 Ronix Koal Fish
Phase Five Scamp (kiddos)
-
07-08-2016, 06:43 PM #15Junior Member
- Join Date
- May 2016
- Location
- Idaho
- Posts
- 16
My mojo started doing the same thing took it in to the dealer and they say it has a safe guard in the system that will shut the system down if the boat speed goes over 15 mph with the plate in the down position. So I have been dropping the plate after the boat planes and is at is surfing speed. No more problems so far.
Sent from my SM-G900V using Tapatalk2016 mojo red&white
2.0 auto flow surf system 2500# ballast
-
07-09-2016, 12:05 AM #16
-
07-09-2016, 02:07 PM #17Senior Member
- Join Date
- Jan 2014
- Location
- Kelowna, BC Canada
- Posts
- 426
We are having the exact same issue ... turns out they actuators are faulty. I figured it out when I put it on the lift and cycled through the various %'s. It would say that it was at 30-40% engaged but the plate was fully engaged. Then when backing it off it would say 60-70% and it would be 0%.
They are replacing them on Tuesday so we will see.
The wave is really inconsistent from rider to rider even run to run. Sometimes it would look amazing ... then 5 mins later it would be shit.2014 Black/White Mojo
345HP Surf Motor
1235 Prop
Autoflow 2.0 Upgrade
1100# FlyHigh Rears
650# IBS
4 x Exile SXT9q's w/ Exile 30.2 amp and Exile ZLD controller
Exile Javelin Amp
10" Rockford sub
-
07-11-2016, 10:18 AM #18
Upgrading the AutoFlow to the new 2.0
Keep me informed on what they figure out if you wouldn't mind. My goofy wave has been doing that for a while now, but I had just assumed it was wind/weeds/shallow water until it happened in 60ft of water this weekend. I'm experiencing exactly what you described.
Sent from my SM-G900W8 using Tapatalk2016 Craz.
Enzo bags.
-
07-11-2016, 02:51 PM #19
This is what I think is happening to me. They are not completely engaging. Find out when it gets back from the dealer.
2016 Craz Surf Addition
The Purple Blurrrrrr
-
07-11-2016, 03:12 PM #20