Results 11 to 20 of 20
-
07-21-2014, 10:17 AM #11
take it apart and hook to a 12 v battery and see if it works. I use my jumper pack all the time to test things.
The Wal-Mart one had cut wires no harness, plus that harness does not match what SC uses, the deutch plugs
http://www.deutschconnector.com/prod...ay_connectors/Last edited by jmvotto; 07-21-2014 at 10:20 AM.
A Day at the Lake...Priceless
A Day in Powder...Endless
Joe V
2012 Möbius XLV~ Loaded & Exiled
2007 Outback V ~ sold
-
07-21-2014, 10:47 AM #12
I went through this last year and replaced mine. I used to know where to order the triangle plug from but I cant remember at the moment. I redid mine and shrink wrapped all the new wiring with my heat gun. Note: Make sure when you install the new one to get it at the lowest point in the hull to help with the water.
2014 Moomba Mobius LSV
2005 Moomba Mobius LSV - Sold
-
07-21-2014, 10:56 AM #13Senior Member
- Join Date
- Jun 2007
- Posts
- 883
2006 Moomba Mobius LSV
Stereo: Kenwood KMR-D562BT
Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"[/SIZE]
-
07-21-2014, 12:01 PM #14
the above link has the triangle plug as well. SC uses the square two pin.
A Day at the Lake...Priceless
A Day in Powder...Endless
Joe V
2012 Möbius XLV~ Loaded & Exiled
2007 Outback V ~ sold
-
08-12-2014, 04:58 PM #15Senior Member
- Join Date
- Jun 2007
- Posts
- 883
btw, repair was quick and easy... remembered how bad I am at soldering. the heat shrink made it look good though..
note: know what took down the old bilge? it sucked up a piece of plastic of some sort... burned itself out auto bilging overnight.2006 Moomba Mobius LSV
Stereo: Kenwood KMR-D562BT
Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"[/SIZE]
-
08-12-2014, 10:45 PM #16
Heat shrink makes us all look like pros! (Except for the guy who set the soldering iron down on the seat and burned a hole through it.)
My Mom said I'm not allowed to get wet!
2008 LSV (sold)
2000 Outback LS (sold)
LLTR!!!!!!!!
-
08-12-2014, 10:56 PM #17Senior Member
- Join Date
- Jun 2007
- Posts
- 883
2006 Moomba Mobius LSV
Stereo: Kenwood KMR-D562BT
Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"[/SIZE]
-
08-12-2014, 11:02 PM #18
I always brought a cardboard box in the boat with extra card board inside to make the soldering iron stays in the box or above the box, plus one on heat shrink.
Glad it was a fairly straight forward fix.A Day at the Lake...Priceless
A Day in Powder...Endless
Joe V
2012 Möbius XLV~ Loaded & Exiled
2007 Outback V ~ sold
-
08-12-2014, 11:20 PM #19
Well, I had a "matt" down and then bumped the cord, twisted the iron right off the matt and smelled the result.
My Mom said I'm not allowed to get wet!
2008 LSV (sold)
2000 Outback LS (sold)
LLTR!!!!!!!!
-
08-12-2014, 11:41 PM #20Senior Member
- Join Date
- Jun 2007
- Posts
- 883