Results 31 to 40 of 48
Thread: No more wet lockers.
-
09-18-2014, 06:09 PM #31
Good to know, I'll definitely be doing this as well, that carpet back there is a real pain in the arse.
2008 Moomba Outback V
2002 Eagle E6 Sabre Jet Boat - Sold
-
09-19-2014, 05:19 PM #32Senior Member
- Join Date
- Jun 2007
- Posts
- 883
Is this stuff too strong? I don't want to burn through my hull like the acid in aliens.
Last edited by spyder; 09-19-2014 at 05:21 PM.
2006 Moomba Mobius LSV
Stereo: Kenwood KMR-D562BT
Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"[/SIZE]
-
09-19-2014, 07:52 PM #33
Last edited by Rakkasan; 09-19-2014 at 07:55 PM.
2008 LSV on the way out
'17 CRAZ!!! on the way in
-
09-19-2014, 09:20 PM #34Senior Member
- Join Date
- Jun 2007
- Posts
- 883
Canadian pricing..
haven't decided about doing the sides yet..
about an hours work scraping with my tanto blade knife and some soapy water later left me with this..
I just want to note, QC at Moomba's factory is shit... the plastic boards that protect the locker from the engine.. the screws were put in so crooked, they stick out the side...
pictures tomorrow.Last edited by spyder; 09-19-2014 at 09:23 PM.
2006 Moomba Mobius LSV
Stereo: Kenwood KMR-D562BT
Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"[/SIZE]
-
09-20-2014, 09:21 AM #35Senior Member
- Join Date
- Jun 2007
- Posts
- 883
Quality work by Skiers Choice right here.. all of the boards had screws the same way.. I sure hope the guys who do this work aren't the ones who put the rest of the boat together.
2006 Moomba Mobius LSV
Stereo: Kenwood KMR-D562BT
Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"[/SIZE]
-
10-03-2014, 06:52 AM #36Senior Member
- Join Date
- Jun 2007
- Posts
- 883
since the just did the floor on mine for now, anyone have any advice on a good carpet glue to stick the wall carpet back on decently? nothing too messy, in case i want to remove it and bed liner the sides later.
2006 Moomba Mobius LSV
Stereo: Kenwood KMR-D562BT
Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"[/SIZE]
-
10-03-2014, 08:55 AM #37
3M spray adhesive
-
10-03-2014, 09:10 AM #38
x2^^ 3M Super 77
make sure you spray the side wall and spray the carpet. Then be sure to wait 30 seconds to a minute before sticking the two together. I like to use a j-roller .
http://www.lowes.com/pd_290286-16878...ductId=30306912008 Mobius LSV
1100#er's in the lockers
ski locker sac
IBS
Johnson reversibles
3 vent heater (which my family loves)
-
10-06-2014, 10:20 PM #39Senior Member
- Join Date
- Jun 2007
- Posts
- 883
couple of complaints, the rear dividers are no longer long enough to reach because of the removal of the carpet thickness, so i needed to use some thin rubber i have laying around... and the fiberglass is absolutely garbage in the moomba in the rear locker floor... had to drill new holes and they still spun and won't hold..
2006 Moomba Mobius LSV
Stereo: Kenwood KMR-D562BT
Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"[/SIZE]
-
05-04-2015, 10:24 AM #40Senior Member
- Join Date
- Jun 2007
- Posts
- 883
i've dedicated a bit more time to this since out of storage... i've removed all carpeting in the rear storage lockers... still need to remove the glue from the walls..goo gone wasn't working for me.. will stop by store tonight and look for something better
2006 Moomba Mobius LSV
Stereo: Kenwood KMR-D562BT
Ballast: 750 Surfside locker, 400 Surfside mid boat, 400 Gravity I, 400 Bow
Surfboards: Inland Surfer Red Woody, Triple X Composite X 58"[/SIZE]