Results 1 to 9 of 9
  1. #1

    Default MOTOR MOUNTS Please Read Last Post

    I have a motor mount that is not looking too good.. its been getting progressively worse for about a year and I think its about time to fix it. has anybody done this? Can I just pull that bolt out and put it back in? do I need to replace that grommet? will I have to do an engine alignment after?

    Any info would be much appreciated.

    20140527_131520.jpg20140527_131451.jpg
    2007 LSV

  2. #2
    Join Date
    Jul 2011
    Location
    Murrieta, CA
    Posts
    1,590

    Default Motor Mounts

    Skidm has the bushing needed. You can replace the bushing without removing the whole mount. Alignment will be required afterwards.
    2018 Max with a little extra weight here and there

  3. #3

    Default

    Is this the right part? of course it has to be the most expensive one on the site.. the PCM one is $3.

    http://www.skidim.com/prodinfo.asp?number=53-6005
    2007 LSV

  4. #4
    Join Date
    Jul 2011
    Location
    Murrieta, CA
    Posts
    1,590

    Default Motor Mounts

    Quote Originally Posted by ABC View Post
    Is this the right part? of course it has to be the most expensive one on the site.. the PCM one is $3.

    http://www.skidim.com/prodinfo.asp?number=53-6005
    I believe that is the one but I would recommend calling them to confirm. They are nice people.
    2018 Max with a little extra weight here and there

  5. #5
    Join Date
    May 2009
    Location
    North End Lake Lanier GA
    Posts
    8,155

    Default

    Do a search on the forum. Pretty sure doc did a write up on this.
    Malo <--- Means--Evil or Mean One. This explains a lot.
    2013 Mojo 2.5 Skylon Tower. Bestia < Beast >
    [COLOR="#696969"]

  6. #6
    Join Date
    Jul 2002
    Location
    London Ontario Canada
    Posts
    2,259

    Default

    https://forum.moomba.com/showthread....ighlight=mount


    here is the write up with a video. your left one looks bad, yes you need to check and adjust the alignment. Be sure to inspect the the top of the mount for any casting defect as this is usually why they fail like the one on the left......there were some bad castings.....the top should be flat and a rounded internal edge otherwise the upward lip chews thru the rubber.....a file or small air grinder works well as the metal is not that hard to smooth
    09 21v LAUNCH

    99 Outback LS. Sold


    run your engine after you change your oil
    68 th Member. WS420,HSE Revolution, OJ 466, Acme1157,1100 sacs,Kicker HLCD's n IX500.4, Supra Coolies
    Doug

  7. #7
    Join Date
    Jul 2002
    Location
    London Ontario Canada
    Posts
    2,259

    Default

    Guys , I am Stickying this as everyone should check their rubber bushings. The first pic in this thread is a relatively normal looking one , the second shows significant wear and needs to be replaced. You can also check the underside for settling as the washer and nut will be loose. It is an easy diy project and the bushings inexpensive.
    09 21v LAUNCH

    99 Outback LS. Sold


    run your engine after you change your oil
    68 th Member. WS420,HSE Revolution, OJ 466, Acme1157,1100 sacs,Kicker HLCD's n IX500.4, Supra Coolies
    Doug

  8. #8
    Join Date
    Aug 2007
    Location
    Alpine, Utah
    Posts
    191

    Default

    How do you check the alignment?
    Garn
    2007 Mobius LS (Direct Drive)

  9. #9
    Join Date
    Jul 2002
    Location
    London Ontario Canada
    Posts
    2,259

    Default

    There is a sticky in the how to section on this.......it's very simple once you've done it

    https://forum.moomba.com/showthread....intenance-Item
    Last edited by DOCDRS; 10-27-2014 at 08:58 PM.
    09 21v LAUNCH

    99 Outback LS. Sold


    run your engine after you change your oil
    68 th Member. WS420,HSE Revolution, OJ 466, Acme1157,1100 sacs,Kicker HLCD's n IX500.4, Supra Coolies
    Doug

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •