Page 1 of 3 123 LastLast
Results 1 to 10 of 21
  1. #1
    Join Date
    Dec 2012
    Location
    Trois-Rivieres, Quebec
    Posts
    196

    Default OZ HD tower on 2014 Mondo

    Anyone has seen the thread below?

    https://forum.moomba.com/showthread....n-lowered-down

    Does anyone has tried that on a Mondo? Is it the same? I will have to adjust the cable for sure if I want to fit the boat in my garage...
    Sampp

    2014 Mondo

    Could be worst
    From nice Québec..

  2. #2
    Join Date
    Aug 2008
    Location
    Hilliard, Ohio
    Posts
    794

    Default

    Sampp, Just had some time to check out my Mondo on the trailer.
    From the factory the screw looks to have adjustment of about an 1" or so.
    Currently my tower is at 84.5" but the jack is high. I should have more time this week to adjust and get her under the 83" I hope. The problem I have is the fixed racks on the upper points will have to come off, not sure if I will order a second set of swivel or what at this point.

  3. #3
    Join Date
    Dec 2012
    Location
    Trois-Rivieres, Quebec
    Posts
    196

    Default

    Quote Originally Posted by patrick232 View Post
    Sampp, Just had some time to check out my Mondo on the trailer.
    From the factory the screw looks to have adjustment of about an 1" or so.
    Currently my tower is at 84.5" but the jack is high. I should have more time this week to adjust and get her under the 83" I hope. The problem I have is the fixed racks on the upper points will have to come off, not sure if I will order a second set of swivel or what at this point.
    I think mine is up to 7'3" with the wake tow on top of the tower. I didn't have à l'éveil when I to ok the measure.
    I'm thinking about butine some smaller wheel and tire and swap just before backing the boat in the garage.
    My new boat is still at the dealer, so not that easy to make some other measures...
    Sampp

    2014 Mondo

    Could be worst
    From nice Québec..

  4. #4
    Join Date
    Aug 2008
    Location
    Hilliard, Ohio
    Posts
    794

    Default

    I did not look at the wake tow point, will have to look at that too.

  5. #5
    Join Date
    Aug 2008
    Location
    Hilliard, Ohio
    Posts
    794

    Default

    It won't go in the garage due to the tower tow point. Might look at dropping the trailer closer to the tires. Think there was a how to on it.

  6. #6
    Join Date
    Oct 2008
    Location
    Central, Arkansas
    Posts
    847

    Default

    Quote Originally Posted by Sampp1963 View Post
    Anyone has seen the thread below?

    https://forum.moomba.com/showthread....n-lowered-down

    Does anyone has tried that on a Mondo? Is it the same? I will have to adjust the cable for sure if I want to fit the boat in my garage...
    Should be the same, you can lower quite a bite. I am pretty sure it is only one size OZ tower ('14) that is used for the all boats. That being said you will have different lowering levels between a Mojo and a Mondo since the cabin area is a little smaller on the Mondo.

    What axles do you have on the trailer, torsion or springs?

  7. #7
    Join Date
    Jul 2008
    Location
    Snellville, GA & Lake Sinclair
    Posts
    8,419

    Default

    Quote Originally Posted by mcdye View Post
    I am pretty sure it is only one size OZ tower ('14) that is used for the all boats.
    LSV, Mondo & Mojo all have the larger diameter tower (know as HD in 2013) while the Outback V still uses the smaller diameter tower.

  8. #8
    Join Date
    Jul 2013
    Location
    Cedar Falls, IA
    Posts
    700

    Default OZ HD tower on 2014 Mondo

    If you physically measure the OD of the towers, what are the measurements of the OZ and OZ HD? I'm getting 1.895" with calipers on my tower.


    Sent from my iPhone using Tapatalk
    2022 Moomba Mojo
    2013 Moomba Mojo 2.5 (sold)

    Tow - 2019 Ford F150 Ecoboost

  9. #9
    Join Date
    May 2009
    Location
    North End Lake Lanier GA
    Posts
    8,155

    Default

    Quote Originally Posted by uniwarking View Post
    If you physically measure the OD of the towers, what are the measurements of the OZ and OZ HD? I'm getting 1.895" with calipers on my tower.


    Sent from my iPhone using Tapatalk
    Not positive but HD is over 2inch.
    From your profile pictures you have the standard tower diameter.
    Malo <--- Means--Evil or Mean One. This explains a lot.
    2013 Mojo 2.5 Skylon Tower. Bestia < Beast >
    [COLOR="#696969"]

  10. #10
    Join Date
    Jul 2008
    Location
    Snellville, GA & Lake Sinclair
    Posts
    8,419

    Default

    I think standard Oz is 1 7/8"

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •