Results 81 to 90 of 103
-
02-17-2014, 05:16 PM #81
Not Boat Related, but Stereo Related
Looks great and will last a lifetime -- much better than anything you could find in a store. Not to mention the pride you taking in making something of that kind of quality!!
If I may brag for a minute....I spent several months planning and building a bar for my basement and it still looks great some 10+ yrs later. All hand made including the oak bar rail which was a real bitch.
ImageUploadedByTapatalk1392671846.148939.jpgImageUploadedByTapatalk1392671857.447613.jpgImageUploadedByTapatalk1392671869.381720.jpg
2013 Outback V
2003 SeaRay 182 -- gone but not forgotten...Mike
2013 Outback V
- ballast: 900# rears / 400# center / 650# IBS
- audio: Exile SXT9Q x 2 towers / Kicker KM65 x 6 cabins / Xi 12 sub / Javelin & XM15.4 amps / ZLD
- FAE
- DIY suckgate
2003 SeaRay 182 -- gone but not forgotten...
-
02-17-2014, 05:22 PM #82
-
02-21-2014, 01:36 PM #83
Those are some really nice bars!
-Mark
14 Mojo - 72 hours and growing
02 Mobius LSV ---- Sold and always will be remembered as the one that started it all.
"Hey you only live once"
-
02-21-2014, 03:59 PM #84
With the quality of work you have posted, you should be doing this for a living. Nice job!
2008 Moomba Mobius LSV Ballast III (stock), Heater, Roswell Quad Spin Pro, Bimini
-
02-25-2014, 12:35 PM #85
Staining and sealing have started. I still need to finish molding the edge detail on lower bar surfaces before they get sanded and sealed. I need to stain and seal the uppoer cabinets too, then stain and seal the equipment racks, (not shown). Still a ways out but the pics here show a good representation of what it will look like.
Me likey!
-
02-25-2014, 12:36 PM #86
Damm fine work !
Hey, Its Moomba time
Its all about the dash - enjoy the dash, as that is your time between the dates
13 Mobius LSV-sold
08 Mobius LSV-sold
03 Mobius LSV-sold
life is about finding the balance between being a responsible adult and staying young at heart
-
02-25-2014, 12:47 PM #87
-
02-25-2014, 12:50 PM #88
Ugh.....always loved the building but hated the finishing......as expected it looks awesome!!
How many coats of poly on the top?Mike
2013 Outback V
- ballast: 900# rears / 400# center / 650# IBS
- audio: Exile SXT9Q x 2 towers / Kicker KM65 x 6 cabins / Xi 12 sub / Javelin & XM15.4 amps / ZLD
- FAE
- DIY suckgate
2003 SeaRay 182 -- gone but not forgotten...
-
02-25-2014, 01:34 PM #89
4 so far. I am a wood boat restorer on occasion, so I am used to taking a month to get a good build, (20 coats) of exterior UV boat show varnish. I am pickey.... The wood boat experience has taught me some things to do to speed up finish work. Rolll-and-tip is one trick. Us a small foam roller to quickly get your finish material on , then just drag a wet brush through it to remove roller texture and bubbles. You can put a coat on this bar top in about two minutes in this manner....
I am using something different here, based on some preliminary samples. Tests so far tell me it is really a good product for this application. I am using a water-based polyurethane from Rustoleum... I have a UV radiant heater in my shop. I am able to bring the wood up to a temp, then shut the heater off while I am applying the finish. Turn the heater on and in about 20 minutes it is ready for over-coating...
Easy easy east easy.... I was concerned I would not get a build of material that gave the top that deep water-soaked wet look but I am wrong. The grain is popping already with just 4 coats and shows a lot of depth contrast from board to board.
The build is thick enough now for a scuff sanding to flatten the high spots. Then 4 more coats and I will see where things are. At this point I am not trying for a thicker coating, as I think I already have sufficient build thickness. I am looking for a flat coating; one that doesn't have the grain texture telegraphed through as microscopic high and low spots. The sanding after these 4 coats will tell me how flat and filled the grain is after these coats. It is Hard Rock Maple; I really don't think it will take 20 coats like that porous old teak and mahogany we work with on boats....Last edited by philwsailz; 02-25-2014 at 01:39 PM.
-
02-25-2014, 01:58 PM #90
I love the quick drying poly as well, mostly because I lack the patience. I tend to use a fairly simple method with my poly.......very thin coats using a foam brush followed by light steel wool and then cleaned with a tack cloth just prior to next coat. And I can usually get 2-3 coats per brush (depending on the project size) by dropping it into a sealed sandwich bag between coats.
I would think 5-10 coats should be more than enough to give you years of beauty and durability.Mike
2013 Outback V
- ballast: 900# rears / 400# center / 650# IBS
- audio: Exile SXT9Q x 2 towers / Kicker KM65 x 6 cabins / Xi 12 sub / Javelin & XM15.4 amps / ZLD
- FAE
- DIY suckgate
2003 SeaRay 182 -- gone but not forgotten...